High-level synthesis tools, both commercial and academic, typically rely on static
scheduling to produce high-throughput pipelines. However, in applications with unpredictable
memory accesses or irregular control flow, these tools need to make pessimistic scheduling
assumptions. In contrast, dataflow circuits implement dynamically scheduled circuits,
in which components communicate locally using a handshake mechanism and exchange data
as soon as all conditions for a transaction are satisfied. Due to their ability to
adapt the schedule at runtime, dataflow circuits are suitable for handling irregular
and control-dominated code. This paper describes Dynamatic, an open-source HLS framework
which generates synchronous dataflow circuits out of C/C++ code. The purpose of this
paper is to give an introductory overview of Dynamatic and demonstrate some of its
use cases, in order to enable others to use the tool and participate in its development.

Since FPGAs are now available in datacenters to accelerate applications, providing
FPGA hardware security is a high priority. FPGA security is becoming more serious
with the transition to FPGA-as-a-Service where users can upload their own bitstreams.
Full control over FPGA hardware through the bitstream enables attacks to weaken an
FPGA-based system. These include physically damaging the FPGA equipment and leaking
of sensitive information such as the secret keys of crypto algorithms. While there
is no known attacks in the commercial settings so far, it is not so much a question
of if but more of when? The tutorial will show concrete attacks applicable on datacenter
FPGAs. The goal of this tutorial is to prepare the FPGA community to impending security
issues in order to pave way for a proactive security. First, we will give a tour through
the FPGA hardware security jungle surveying practical attacks and potential threats.
We will reinforce this with live demos of denial of service attacks. Less than 10%
of the logic resources on an FPGA can draw enough dynamic power to crash a datacenter
FPGA card. In the second part of the tutorial, we will show different mitigations
that are either vendor supported or proposed by the academic community. In summary,
the tutorial will communicate that while FPGA hardware security is complicated to
bring about, there are acceptable solutions for known FPGA security problems.

In recent years, substantial attention has been drawn to vulnerabilities in the architectural
design of microelectronics, as well as the security of their global supply chains.
In reality, establishing trust in microelectronics requires broader considerations,
from verification of the software leveraged to implement hardware designs, to analyzing
third-party intellectual property cores, all the way to run-time design assurance
and periodic device screening post-deployment. These concerns are relevant to stakeholders
at all levels, from small independent design houses all the way to multi-national
strategic interests. One notable example of the latter is the U.S. Department of Defense’s
Trusted and Assured Microelectronics (T&AM) program, which seeks assured access to
state-of-the-art foundries through modern trust and assurance methods and demonstrations
[1]. This talk will describe research efforts at the Georgia Tech Research Institute
centered around providing assurance of FPGAs. Current research thrusts include the
development of verification techniques at multiple stages of the design process, including
vendor design software execution, implementation of user designs, and even the operation
of the underlying physical device hardware itself. For example, to address trust in
synthesis and implementation of high-level user source code, we discuss the development
of canary circuits which are compiled alongside user design circuits and can be independently
inspected and verified to ensure adherence to user-defined implementation rules. Additionally,
we discuss one avenue for providing trust in vendor hardware devices through our development
of Independent Functional Test (IFT) suites.

Cloud FPGAs have been gaining interest in recent years due to the ability of users
to request FPGA resources quickly, flexibly, and on-demand. In addition to the existing
single-tenant deployments, where each user gets an access to a whole FPGA, recent
academic proposals have looked at creating multi-tenant deployments, where multiple
users share a single FPGA, e.g., [3]. In both settings, there is a large amount of
infrastructure and physical resources that are shared among users. Sharing of the
physical resources in data centers and processors is well known to lead to potential
attacks, e.g., [4]. However, only recently have there been demonstrations of various
security attacks that our group and others have shown to be possible in Cloud FPGA
setting, e.g., [5].

This talk will discuss Cloud FPGA security from the perspective of side and covert
channel attacks that arise due to these shared resources. It will first cover our
recent work on thermal channels that can be used to create covert channels between
users renting same FPGA over time [5]. These channels can create stealthy communication
medium for leaking small amounts of sensitive information, e.g., cryptographic keys.
As defense strategies, the talk will point out possible solutions at the system level
and at the hardware level. At the system level, adding delays between when different
users can access the same FPGA, or preventing users from being able to identify unique
FPGA instances can mitigate the threats, but does increase overhead. At the hardware
level, additional cooling to erase thermal information after users uses and FPGA,
or new sensors to monitor FPGAs and generate an alert when excessive heat is detected
are possible solutions that will be discussed.

The talk will also discuss recent work on voltage-based attacks that leverage custom
circuits instantiated inside the FPGAs to measure voltage changes. Voltage-based channels
can be used to leak sensitive information across FPGAs (in single-tenant or multi-tenant
settings) [2], or can be combined with other existing attacks to perform cross-talk
leakage inside the FPGAs (in multi-tenant settings) [1]. These attacks highlight the
power of attacker when they are able to synthesize any circuit into a shared FPGA
environment. Furthermore, even with certain restrictions on the types of designs that
can be synthesized, this talk will show how attacks can be deployed. As defense strategies,
the talk will point out possible new design check rules that can be used by Cloud
FPGA providers.

In light of the attacks and defenses, Cloud FPGA security remains a cat-and-mouse
game. There is then the foremost need to better understand the existing and potential
attacks — to design defenses and deploy them before malicious users try to launch
such attacks. Only with proper understanding of the possible FPGA attacks, can secure
Cloud FPGAs be created.

An emerging trend in the data center is the at-scale deployment of Field-Programmable
Gate Arrays (FPGAs) which combine multi-gigabit and ultra-low latency workload acceleration
with hardware-level reconfigurability. In particular, for applications such as Deep
Learning where techniques and algorithms are rapidly changing, the inherent flexibility
of FPGAs grants them an edge over hardened data processing units such as ASICs or
GPUs. Inevitably, Cloud Service Providers (CSPs) will seek to maximize resource utilization
for their FPGA investments as they currently do for general-purpose computing resources.
Current FPGA deployments in the data center tend to be single-tenant or support multiple
tenants through time multiplexing (temporal multi-tenancy) which can result in resource
underutilization. This approach does not scale and presents challenges for elastic
workloads whose properties are not fully known ahead of time. Instead, we expect that
closing the resource utilization gap will require efficient spatial allocation of
FPGA resources across multiple tenants while maintaining security and QoS guarantees.
In particular, new usage models such as FPGA-as-a-Service, where resources are exposed
directly to the cloud tenant, present unique challenges on the security and QoS side.
In this talk we review the threat landscape and trust models associated with FPGA
multi-tenancy, highlight future research challenges and examine the unique opportunities
that FPGA multi-tenancy enables given adequate guarantees on security and QoS.

Technology and cost are motivating more and more developers to put more and more of
their “secret sauce” in programmable logic. This is great for the consumer as it opens
the market to the smaller players. However, it also opens the market for IP theft;
after all, why spend years making something yourself if you can just pilfer it and
re-brand it as your own. A sad statement for sure but it is the reality of the world
we live in. Worsening the situation is the fact that FPGA’s and SoC’s are starting
to become the anchor for the security of larger systems. This now brings in another
set of bad guys; ones that are tech savvy and armed with lab equipment. They are not
looking for your IP but are looking to break into the system your IP is protecting.
The number of adversaries is growing just as fast as the markets for the devices themselves
and is quickly becoming an arms race.

The first volley was fired when the adversaries started reverse engineering the programming
files (bitstreams) so we added bitstream encryption (3-DES at the time). However,
commercial computational power rendered that algorithm obsolete, so we moved to AES-256.
The adversary gave up attacking the algorithm and started going after the key itself,
so we added physical protections. Failing to break into the device they opted for
less physically invasive attacks such as Differential Power Analysis, so we added
authentication before decryption and key rolling. Frustrated with these and other
protections the adversary went back to physical attacks. This was aided by the ever-expanding
capabilities of Failure Analysis which needs the same equipment to understand device
failures as attackers need to break into devices. They started with circuit probing
and edits using the Focus Ion Beam (FIB). This allowed them to disable security features
or tap into the key space. To counter this redundancy and circuit obfuscation techniques
were added. They then switched to less destructive imaging methods which forced us
to levy system requirements (detection and prevention techniques) on the customer;
costly but effective.

The security of FPGAs and SoCs has greatly evolved over the years but the next battlefield
in the arms race is on the horizon: FPGAs / SoC’s in the cloud. Most of the security
in modern day devices primarily considers an attacker on the outside of the device
with close physical access. As such, most of the mitigations make a similar assumption.
However, devices in the cloud creates an entire new form of device warfare; remote
attacks on FPGAs and SoCs. This is not an issue of hacking software; that has been
around since before the internet. It is about the number of devices in the cloud that
are programmable and, therefore, hackable. Side channel attacks such as row-hammer
(1) and CLKscrew (2) show that if there are secrets and some level of device access,
the attackers will find a way to exploit it. In this modern era, security engineers
are going to have to look for adversaries where they would never expect them; inside
the system.

FPGAs have been deployed in datacenters worldwide and are now available for use by
in both public and private clouds. Enormous focus has been given to optimizing machine
learning workloads for FPGAs, especially for deep neural networks (DNNs) in areas
like web search, image classification, and translation. However, major cloud applications
encompasses a variety of areas that aren’t primarily machine learning workloads, including
databases, video encoding, text processing, gaming, bioinformatics, productivity and
collaboration, file hosting and storage, e-mail, and many more. While machine learning
can certainly play a role in each of these areas, is there more that can be done to
accelerate these more traditional workloads? Even more challenging than identifying
promising workloads is figuring out how developers can practically create and deploy
useful applications using FPGAs to the cloud. While FPGAs-as-a-Service allow access
to FPGAs in the cloud, there is a huge gap between raw programmable hardware and a
customer paying money to use an application powered by that hardware. A wide variety
of FPGA IP exists for developers to use, but individual IP blocks are a long way from
being a fully functional cloud application. Building block IPs like Memcached, regex
matching, protocol parsing, and linear algebra are only a subset of the necessary
functionality for full cloud applications. Developing or acquiring IP and integrating
it into a full application that customers will pay for is a significant task. And
even when a customer pays, how should the money be distributed between IP vendors.
Should it be a onetime fee? By usage? By number of FPGAs deployed? Who should have
the burden for support if something goes wrong? In traditional cloud applications,
FPGA IP block functions are implemented in software libraries. However, few examples
of optimized software libraries are commercially successful, so is selling FPGA IP
even a viable commercial model for cloud applications? High-level synthesis (HLS)
tools promise to provide one path to enable software developers to make effective
use of FPGAs for computing tasks, but are any tools really capable of accelerating
cloud-scale applications? Many HLS tools require substantial microarchitectural guidance
in the form of pragmas or configuration files to come out with good results. Real
cloud applications also rarely have a single dominant function and have significant
data movement, so without proper partitioning and tuning, the acceleration gains from
the FPGA are quickly wiped out by data movement and Amdahl’s Law. This panel will
gather experts in using FPGAs for cloud application areas beyond machine learning,
and how those applications can be built and successfully deployed. We will cover topics
such as: -What are the most important cloud workloads for FPGAs to target besides
machine learning? -Are there specific changes to the FPGA architecture that would
benefit these cloud applications? -What are the economic models that will work for
IP developers, application developers, and cloud providers? -How can we make development
of FPGA applications easier for the Cloud? -Will open source IP make it impossible
for IP vendors to make commercially successful libraries? -What advances are necessary
for HLS tools to be practical in the Cloud? The panel is comprised of experts in applications,
IP development, and cloud deployment. Each will give a short presentation of what
they find as the most important applications and how they see FPGA development for
the cloud going forward, then we will open the floor to an interactive discussion
with the audience.

Spatial compute architectures, like Field Programmable Gate Arrays (FPGAs), constitute
a key architectural pillar in modern heterogeneous compute platforms. Spatial architectures
need a sophisticated Electronic Design Automation (EDA) compiler to optimally map
and fit a user’s workload/design onto the underlying spatial device. This EDA compiler
not only helps users to custom-configure the spatial device but is also critically
required for architectural exploration of new spatial architectures. The FPGA industry
has had a long history of innovation in this symbiotic relationship between EDA and
reconfigurable spatial architectures.

This talk will walk down the memory lane of multiple waves of such innovation, amplifying
how the complexity of EDA technology has not only scaled with Moore’s law scaling
of size and complexity of silicon hardware, but also how it has been pivotal in the
architectural design of modern FPGAs. A general overview of modern FPGA EDA flows
and key differences compared to Application-Specific Integrated Circuit (ASIC) EDA
flows will be discussed. State-of-the-art FPGAs, Stratix® 10 and AgileX™ from Intel
incorporate an advanced register-rich HyperFlex™ architecture that introduces disruptive
optimization opportunities in the EDA compiler. Such physical synthesis optimization
technologies like logic retiming, clock skew optimization, time borrowing, and their
synergies and challenges will be discussed. Solving these challenges enables FPGAs
to achieve non-linear performance improvements.

Logic retiming was first introduced as a powerful sequential design optimization technique
three decades ago, yet gained limited popularity in the ASIC industry, because of
the lack of scalable sequential verification techniques. This talk will highlight
the root causes of this issue and present innovations in retiming technology and constrained
random simulation that allow the successful verification of retimed circuits, thereby
enabling the use of logic retiming for FPGAs.

FPGAs have traditionally targeted Register-Transfer Level (RTL) designers. To enable
wider adoption of FPGAs, Intel has developed several High-Level Design (HLD) tools,
frameworks, libraries, and methodologies, raising the level of programming abstraction.
This talk will provide a glimpse into Intel’s HLD offerings that enable software developers
in the broader ecosystem to leverage FPGAs.

Academic researchers will also be provided with some key research vectors to help
propel the FPGA industry further.

In cloud computing, software is transitioning from monolithic to microservices architecture
to improve the maintainability, upgradability and the flexibility of the applications.
They are able to request a service with different implementations of the same functionality,
including hardware accelerator, depending on cost and performance. This model opens
up a new opportunity to integrate reconfigurable hardware, specifically, FPGA, in
the cloud to offer such services. There are many research works discussing solutions
for this problem but they focus primarily on the high-level aspects of resource manager,
hypervisor or hardware architecture. The low-level physical design choices of FPGA
to maximize the accelerator allocation success rate (called serviceability) is largely
untouched. In this paper, we propose a design space exploration algorithm to determine
the best configuration of partially reconfigurable regions (PRRs) to host the accelerators.
Besides, the algorithm is capable of estimating the actual resources occupied by the
PRRs on the FPGA even before floorplanning. We systematically study the effects of
having more PRRs on the system in various aspects, i.e., serviceability, waiting time
and resource wastage. The experiments show that at a certain number of PRRs, upto
91% serviceability can be achieved for 12 concurrent users. It is a significant improvement
from 52% without our approach. The average amount of time that each request has to
wait to be served is also reduced by 6.3X. Furthermore, the cumulative unused FPGA
resources is reduced almost by half.

Recent breakthroughs in Deep Neural Networks (DNNs) have fueled a growing demand for
domain-specific hardware accelerators (i.e., DNN chips). However, designing DNN chips
is non-trivial because: (1) mainstream DNNs have millions of parameters and billions
of operations; (2) the design space is large due to numerous design choices of dataflows,
processing elements, memory hierarchy, etc.; and (3) there is an algorithm/hardware
co-design need for the same DNN functionality to have a different decomposition that
would require different hardware IPs and thus correspond to dramatically different
performance/energy/area tradeoffs. Therefore, DNN chips often take months to years
to design and require a large team of cross-disciplinary experts. To enable fast and
effective DNN chip design, we propose AutoDNNchip – a DNN chip generator that can
automatically produce both FPGA- and ASIC-based DNN chip implementation (i.e., synthesizable
RTL code with optimized algorithm-to-hardware mapping) from DNNs developed by machine
learning frameworks (e.g., PyTorch) for a designated application and dataset without
humans in the loop. Specifically, AutoDNNchip consists of 2 integrated enablers: (1)
a Chip Predictor, which can accurately and efficiently predict a DNN accelerator’s
energy, throughput, latency, and area based on the DNN model parameters, hardware
configurations, technology-based IPs, and platform constraints; and (2) a Chip Builder,
which can automatically explore the design space of DNN chips (including IP selections,
block configurations, resource balancing, etc.), optimize chip designs via the Chip
Predictor, and then generate synthesizable RTL code with optimized dataflows to achieve
the target design metrics. Experimental results show that our Chip Predictor’s predicted
performance differs from real-measured ones by <10% when validated using 15 DNN models
and 4 platforms (edge-FPGA/TPU/GPU and ASIC). Furthermore, DNN accelerators generated
by our AutoDNNchip can achieve better (up to 3.86X improvement) performance than that
of expert-crafted state-of-the-art FPGA- and ASIC-based accelerators, showing the
effectiveness of AutoDNNchip. Our open-source code can be found at https://github.com/RICE-EIC/AutoDNNchip.git.

The domain-specific language (DSL) for image processing, Halide, has generated a lot
of interest because of its capability of decoupling algorithms from schedules that
allow programmers to search for optimized mappings targeting CPU and GPU. Unfortunately,
while the Halide community has been growing rapidly, there is currently no way to
easily map the vast number of Halide programs to efficient FPGA accelerators. To tackle
this challenge, we propose HeteroHalide, an end-to-end system for compiling Halide
programs to FPGA accelerators. This system makes use of both algorithm and scheduling
information specified in a Halide program. Compared to the existing approaches, flow
provided by HeteroHalide is significantly simplified, as it only requires moderate
modifications for Halide programs on the scheduling part to be applicable to FPGAs.
For part of the compilation flow, and to act as the intermediate representation (IR)
of HeteroHalide, we choose HeteroCL, a heterogeneous programming infrastructure which
supports multiple implementation backends (such as systolic arrays and stencil implementations).
By using HeteroCL, HeteroHalide can generate efficient accelerators by choosing different
backends according to the application. The performance evaluation compares the accelerator
generated by HeteroHalide with multi-core CPU and an existing Halide-HLS compiler.
As a result, HeteroHalide achieves 4.15\texttimes speedup on average over 28 CPU cores,
and 2 \textasciitilde 4\texttimes throughput improvement compared with the existing
Halide-HLS compiler.

In recent years, multiple public cloud FPGA providers have emerged, increasing interest
in FPGA acceleration of cryptographic, bioinformatic, financial, and machine learning
algorithms. To help understand the security of the cloud FPGA infrastructures, this
paper focuses on a fundamental question of understanding what an adversary can learn
about the cloud FPGA infrastructure itself, without attacking it or damaging it. In
particular, this work explores how unique features of FPGAs can be exploited to instantiate
Physical Unclonable Functions (PUFs) that can distinguish between otherwise-identical
FPGA boards. This paper specifically introduces the first method for identifying cloud
FPGA instances by extracting a unique and stable FPGA fingerprint based on PUFs measured
from the FPGA boards’ DRAM modules. Experiments conducted on the Amazon Web Services
(AWS) cloud reveal the probability of renting the same physical board more than once.
Moreover, the experimental results show that hardware is not shared among f1.2xlarge,
f1.4xlarge, and f1.16xlarge instance types. As the approach used does not violate
any restrictions currently placed by Amazon, this paper also presents a set of defense
mechanisms that can be added to existing countermeasures to mitigate users’ attempts
to fingerprint cloud FPGA infrastructures.

Combinatorial optimizations are widely adopted in scientific and engineering applications,
such as VLSI design, automated machine learning (AutoML), and compiler design. Combinatorial
optimization problems are notoriously challenging to exactly solve due to the NP-hardness.
Scientists have long discovered that numerically simulating classical nonlinear Hamiltonian
systems can effectively solve many well-known combinatorial optimization problems.
However, such physical simulation typically requires a massive amount of computation,
which even outstrips the logic capability of modern reconfigurable digital fabrics.
In this work, we proposed an FPGA-based general combinatorial optimization problem
solver which achieved ultra-high performance and scalability. Specifically, we first
reformulated a broad range of combinatorial optimization problems with a general graph-based
data structure called the Ising model. Second, instead of utilizing classical simulated
annealing to find an approximate solution, we utilized a new heuristic algorithm,
simulated bifurcation, to search for solutions. Third, we designed an efficient hardware
architecture to fully exploit FPGAs’ potentials to accelerate the algorithm, and proposed
three hardware-software co-optimizations to further improve the performance. By experimenting
on benchmarks, our proposal outperformed the state-of-the-art simulated annealing
optimization solver by up to 10.91 times.

We present a high-throughput FPGA design for supporting high-performance network switching.
FPGAs have recently been attracting attention for datacenter computing due to their
increasing transceiver count and capabilities, which also benefit the implementation
and refinement of network switches. Our solution replaces the crossbar in favour of
a novel, more pipeline-friendly approach, the “Combined parallel round-robin arbiter”.
It also removes the overhead of incorporating an often-iterative scheduling or matching
algorithm, which sometimes tries to fit too many steps in a single or a few FPGA cycles.
The result is a network switch implementation on FPGAs operating at a high frequency
and with a low port-to-port latency. It also provides a wiser buffer memory utilisation
than traditional Virtual Output Queue (VOQ)-based switches and is able to keep 100%
throughput for a wider range of traffic patterns using a fraction of the buffer memory
and shorter packets.

The simulation of light propagation through tissues is important for medical applications,
such as photodynamic therapy (PDT) for cancer treatment. To optimize PDT an inverse
problem, which works backwards from a desired distribution of light to the parameters
that caused it, must be solved. These problems have no closed-form solution and therefore
must be solved numerically using an iterative method. This involves running many forward
light propagation simulations which is time-consuming and computationally intensive.

Currently, the fastest general software solver for this problem is FulMonteSW. It
models complex 3D geometries with tetrahedral meshes and uses Monte Carlo techniques
to model photon interactions with tissues. This work presents FullMonteFPGACL: an
FPGA-accelerated version of FullMonteSW using an Intel Stratix 10 FPGA and the Intel
FPGA SDK for OpenCL. FullMonteFPGACL has been validated and benchmarked using several
models and achieves improvements in performance (4x) and energy-efficiency (11x) over
the optimized and multi-threaded FullMonteSW implementation. We discuss methods for
extending the design to improve the performance and energy-efficiency ratios to 16x
and 17x, respectively. We achieved these gains by developing in an agile fashion using
OpenCL to facilitate quick prototyping and hardware-software partitioning. However,
achieving competitive area and performance required careful design of the hardware
pipeline and expression of its structure in OpenCL. This led to a hybrid design style
that can improve productivity when developing complex applications on an FPGA.

360° panoramic video provides an immersive Virtual Reality experience. However, rendering
360° videos consumes excessive energy on client devices. FPGA is an ideal offloading
target to improve the energy-efficiency. However, a naive implementation of the processing
algorithm would lead to an excessive memory footprint that offsets the energy benefit.
In this paper, we propose an algorithm-architecture co-designed system that dramatically
reduces the on-chip memory requirement of VR video processing to enable FPGA offloading.
Evaluation shows that our system is able to achieve significant energy reduction with
no loss of performance compared to today’s off-the-shelf VR video rendering system.

The real-time synthesis of 3D spatial audio has many applications, from virtual reality
to navigation for the visually-impaired. Head-related transfer functions (HRTF) can
be used to generate spatial audio based on a model of the user’s head. Previous studies
have focused on the creation and interpolation of these functions with little regard
for real-time performance. In this paper, we present an FPGA-based platform for real-time
synthesis of spatial audio using FIR filters created from head-related transfer functions.
For performance reasons, we run filtering, crossfading, and audio output on FPGA fabric,
while calculating audio source locations and storing audio files on the CPU. We use
a head-mounted 9-axis IMU to track the user’s head in real-time and adjust relative
spatial audio locations to create the perception that audio sources are fixed in space.
Our system, running on a Xilinx Zynq Z-7020, is able to support 4X more audio sources
than a comparable GPU and 8X more sources than a CPU while maintaining sub-millisecond
latency and comparable power consumption. Furthermore, we show how our system can
be leveraged to communicate the location of landmarks and obstacles to a visually-impaired
user during a sailing race or other navigation scenario. We test our system with multiple
users and show that, as a result of our reduced latency, a user is able to locate
a virtual audio source with an extremely high degree of accuracy and navigate toward
it.

Multidimensional Long Short-Term Memory (MD-LSTM) neural network is an extension of
one-dimensional LSTM for data with more than one dimension that allows MD-LSTM to
show state-of-the-art results in various applications including handwritten text recognition,
medical imaging, and many more. However, efficient implementation suffers from very
sequential execution that tremendously slows down both training and inference compared
to other neural networks. This is the primary reason that prevents intensive research
involving MD-LSTM in the recent years, despite large progress in microelectronics
and architectures. The main goal of the current research is to provide acceleration
for inference of MD-LSTM, so to open a door for efficient training that can boost
application of MD-LSTM. By this research we advocate that FPGA is an alternative platform
for deep learning that can offer a solution in cases when a massive parallelism of
GPUs does not provide the necessary performance required by the application. In this
paper, we present the first hardware architecture for MD-LSTM. We conduct a systematic
exploration of precision vs. accuracy trade-off using challenging dataset for historical
document image binarization from DIBCO 2017 contest, and well known MNIST dataset
for handwritten digits recognition. Based on our new architecture we implement FPGA-based
accelerator that outperforms NVIDIA K80 GPU implementation in terms of runtime by
up to 50x and energy efficiency by up to 746x. At the same time, our accelerator demonstrates
higher accuracy and comparable throughput in comparison with state-of-the-art FPGA-based
implementations of multilayer perceptron for MNIST dataset.

Lightweight convolutional neural networks (LW-CNNs) such as MobileNet, ShuffleNet,
SqueezeNet, etc., have emerged in the past few years for fast inference on embedded
and mobile system. However, lightweight operations limit acceleration potential by
GPU due to their memory bounded nature and their parallel mechanisms that are not
friendly to SIMD. This calls for more specific accelerators. In this paper, we propose
an FPGA-based overlay processor with a corresponding compilation flow for general
LW-CNN accelerations, called Light-OPU. Software-hardware co-designed Light-OPU reformulates
and decomposes lightweight operations for efficient acceleration. Moreover, our instruction
architecture considers sharing of major computation engine between LW operations and
conventional convolution operations. This improves the run-time resource efficiency
and overall power efficiency. Finally, Light-OPU is software programmable, since loading
of compiled codes and kernel weights completes switch of targeted network without
FPGA reconfiguration. Our experiments on seven major LW-CNNs show that Light-OPU achieves
5.5x better latency and 3.0x higher power efficiency on average compared with edge
GPU NVIDIA Jetson TX2. Furthermore, Light-OPU has 1.3x to 8.4x better power efficiency
compared with previous customized FPGA accelerators. To the best of our knowledge,
Light-OPU is the first in-depth study on FPGA-based general processor for LW-CNNs
acceleration with high performance and power efficiency, which is evaluated using
all major LW-CNNs including the newly released MobileNetV3.

The irregularity of recent Convolutional Neural Network (CNN) models such as less
data reuse and parallelism due to the extensive network pruning and simplification
creates new challenges for FPGA acceleration. Furthermore, without proper optimization,
there could be significant overheads when integrating FPGAs into existing machine
learning frameworks like TensorFlow. Such a problem is mostly overlooked by previous
studies. However, our study shows that a naive FPGA integration into TensorFlow could
lead to up to 8.45x performance degradation. To address the challenges mentioned above,
we propose several SW/HW co-design approaches to perform the end-to-end optimization
of deep learning applications. We present a flexible and composable architecture called
FlexCNN. It can deliver high computation efficiency for different types of convolution
layers using techniques including dynamic tiling and data layout optimization. FlexCNN
is further integrated into the TensorFlow framework with a fully-pipelined software-hardware
integration flow. This alleviates the high overheads of TensorFlow-FPGA handshake
and other non-CNN processing stages. We use OpenPose, a popular CNN-based application
for human pose recognition, as a case study. Experimental results show that with the
FlexCNN architecture optimizations, we can achieve 2.3x performance improvement. The
pipelined integration stack leads to a further 5x speedup. Overall, the SW/HW co-optimization
produces a speedup of 11.5x and results in an end-to-end performance of 23.8FPS for
OpenPose with floating-point precision, which is the highest performance reported
for this application on FPGA in the literature.

This paper describes architectural enhancements in Intel® Agilex™ FPGAs and SoCs.
Agilex devices are built on Intel’s 10nm process and feature next-generation programmable
fabric, tightly coupled with a quad-core ARM processor subsystem, a secure device
manager, IO and memory interfaces, and multiple companion transceiver tile choices.
The Agilex fabric features multiple logic block enhancements that significantly improve
propagation delays and integrate more effectively with the second-generation HyperFlexAgilex™
pipelined routing architecture. Routing connections are re-designed to be point-to-point,
dropping intermediate connections featured in prior FPGA generations and replacing
them with a wider variety of shorter wire types. Fine-grain programmable clock skew
and time-borrowing were introduced throughout the fabric to augment the slack-balancing
capabilities of HyperFlex registers. DSP capabilities are also extended to natively
support new INT9/BFLOAT16/FP16 formats. Together, along with process and circuit enhancements,
these changes support more than 40% performance improvement over the Stratix® 10 family
of FPGAs.

Technology scaling makes metal delay ever more problematic, but routing between Look-Up
Tables (LUTs) still passes through a series of transistors. It seems wise to avoid
the corresponding delay whenever possible. Direct connections between LUTs, both within
and across multiple clusters, can eschew the transistor delays of crossbars, connection
blocks, and switch blocks. In this paper we investigate the usefulness of enhancing
classical Field-Programmable Gate Array (FPGA) architectures with direct connections
between LUTs. We present an efficient algorithm for searching automatically the most
interesting patterns of such direct connections. Despite our methods being fairly
conservative and relying on the use of unmodified standard CAD tools, we obtain a
2.77% improvement of the geometric mean critical path delay of a standard benchmark
set, with improvement ranging from -0.17% to 7.3% for individual circuits. As modest
as these results may seem at first glance, we believe that they position direct connections
between LUTs as a promising topic for future research. Extending this work with dedicated
CAD algorithms and exploiting the increased possibilities for optimal buffering, diagonal
routing, and pipelining could prove direct connections important to the continuation
of performance improvement into next generation FPGAs.

We propose two tiers of modifications to FPGA logic cell architecture to deliver a
variety of performance and utilization benefits with only minor area overheads. In
the first tier, we augment existing commercial logic cell datapaths with a 6-input
XOR gate in order to improve the expressiveness of each element, while maintaining
backward compatibility. This new architecture is vendor-agnostic, and we refer to
it as LUXOR. We also consider a secondary tier of vendor-specific modifications to
both Xilinx and Intel FPGAs, which we refer to as X-LUXOR+ and I-LUXOR+ respectively.
We demonstrate that compressor tree synthesis using generalized parallel counters
(GPCs) is further improved with the proposed modifications. Using both the Intel adaptive
logic module and the Xilinx slice at the 65nm technology node for a comparative study,
it is shown that the silicon area overhead is less than 0.5% for LUXOR and 5-6% for
LUXOR+, while the delay increments are 1-6% and 3-9% respectively. We demonstrate
that LUXOR can deliver an average reduction of 13-19% in logic utilization on micro-benchmarks
from a variety of domains. BNN benchmarks benefit the most with an average reduction
of 37-47% in logic utilization, which is due to the highly-efficient mapping of the
XnorPopcount operation on our proposed LUXOR+ logic cells.

Since the inception of FPGAs over 2 decades ago, the micro-architectures and macro-architectures
of FPGAs across all FPGA vendors have been converging strongly to the point that comparable
FPGAs from the main FPGA vendors had virtually the same use models, and the same programming
models. User designs were getting easier to port from one vendor to the other with
every generation. Recent developments in from different FPGA vendors targeting the
most advanced semiconductor technology nodes are an abrupt and disruptive break from
this trend, especially at the macro-architectural level.

FPGAs provide significant advantages in throughput, latency, and energy efficiency
for implementing low-latency, compute-intensive applications when compared to general-purpose
CPUs and GPUs. Over the last decade, FPGAs have evolved into highly configurable SoCs
with on-chip CPUs, domain-specific programmable accelerators, and flexible connectivity
options. Recently, Xilinx introduced a new heterogeneous compute architecture, the
Adaptive Compute Acceleration Platform (ACAP), with significantly more flexibility
and performance to address an evolving set of new applications such as machine learning.
This advancement on the device side is accompanied by similar advances on higher-level
programming approaches to make FPGAs and ACAPs significantly easy to use for a wide
range of applications. Xilinx Vitis Unified Software Platform is a comprehensive development
environment to build and seamlessly deploy accelerated applications on Xilinx platforms
including Alveo cards, FPGA-instances in the cloud, and embedded platforms. It addresses
the three major industry trends: the need for heterogenous computing, applications
that span cloud to edge to end-point, and AI proliferation. Vitis supports application
programming using C, C++ and OpenCL, and it enables the development of large-scale
data processing and machine learning applications using familiar, higher-level frameworks
such as TensorFlow and SPARK. To facilitate communication between the host application
and accelerators, Xilinx Runtime library (XRT) provides APIs for accelerator life-cycle
management, accelerator execution management, memory allocation, and data communication
between the host application and accelerators. In addition, a rich set of performance-optimized,
open-source libraries significantly ease the application development. Vitis AI, an
integral part of Vitis, enables AI inference acceleration on Xilinx platforms. It
supports industry’s leading deep learning frameworks like Tensorflow and Caffe, and
offers a comprehensive suite of tools and APIs to prune, quantize, optimize, and compile
pre-trained models to achieve the highest AI inference performance on Xilinx platforms.
This talk provides an overview of Vitis and Vitis AI development environments.

Debugging consumes a large portion of FPGA design time, and with the growing complexity
of traditional FPGA systems and the additional verification challenges posed by multiple
FPGAs interacting within data centers, debugging productivity is becoming even more
important. Current debugging flows either depend on simulation, which is extremely
slow but has full visibility, or on hardware execution, which is fast but provides
very limited control and visibility. In this paper, we present StateMover, a checkpointing-based
debugging framework for FPGAs, which can move design state back and forth between
an FPGA and a simulator in a seamless way. StateMover leverages the speed of hardware
execution and the full visibility and ease-of-use of a simulator. This enables a novel
debugging flow that has a software-like combination of speed with full observability
and controllability. StateMover adds minimal hardware to the design to safely stop
the design under test so that its state can be extracted or modified in an orderly
manner. The added hardware has no timing overhead and a very small area overhead.
StateMover currently supports Xilinx UltraScale devices, and its underlying techniques
and tools can be ported to other device families that support configuration readback.
Moving the state from/to an FPGA to/from a simulator can be performed in a few seconds
for large FPGAs, enabling a new debugging flow.

Commercial high-level synthesis tools typically produce statically scheduled circuits.
Yet, effective C-to-circuit conversion of arbitrary software applications calls for
dataflow circuits, as they can handle efficiently variable latencies (e.g., caches)
and unpredictable memory dependencies. Dataflow circuits exhibit an unconventional
property: registers (usually referred to as “buffers”) can be placed anywhere in the
circuit without changing its semantics, in strong contrast to what happens in traditional
datapaths. Yet, although functionally irrelevant, this placement has a significant
impact on the circuit’s timing and throughput. In this work, we show how to strategically
place buffers into a dataflow circuit to optimize its performance. Our approach extracts
a set of choice-free critical loops from arbitrary dataflow circuits and relies on
the theory of marked graphs to optimize the buffer placement and sizing. We demonstrate
the performance benefits of our approach on a set of dataflow circuits obtained from
imperative code.

This paper presents an extension to PathFinder FPGA routing algorithm, which enables
it to deliver FPGA designs free from risks of crosstalk attacks. Crosstalk side-channel
attacks are a real threat in large designs assembled from various IPs, where some
IPs are provided by trusted and some by untrusted sources. It suffices that a ring-oscillator
based sensor is conveniently routed next to a signal that carries secret information
(for instance, a cryptographic key), for this information to possibly get leaked.
To address this security concern, we apply several different strategies and evaluate
them on benchmark circuits from Verilog-to-Routing tool suite. Our experiments show
that, for a quite conservative scenario where 10-20% of all design nets are carrying
sensitive information, the crosstalk-attack-aware router ensures that no information
leaks at a very small penalty: 1.58-7.69% increase in minimum routing channel width
and 0.12-1.18% increase in critical path delay, on average. In comparison, in an AES-128
cryptographic core, less than 5% of nets carry the key or the intermediate state values
of interest to an attacker, making it highly likely that the overhead for obtaining
a secure design is, in practice, even smaller.

Embedded and cyber-physical systems are pervading all aspects of our lives, including
sensitive and critical ones. As a result, they are an alluring target for cyber attacks.
These systems, whose implementation is often based on reconfigurable hardware, are
typically deployed in places accessible to attackers. Therefore, they require protection
against tampering and side-channel attacks. However, a side-channel resistant implementation
of a security primitive is not sufficient, as it can be weakened by an adversary,
aging, or environmental factors. To detect this, legitimate users should be able to
evaluate the side-channel resistance of their systems not only when deploying them
for the first time, but also during their entire service life. The most widespread
and de facto standard methodology for measuring power side-channel leakage uses Welch’s
t-test. In practice, collecting the data for the t-test requires physical access to
the device, a device-specific test setup, and the equipment for measuring the power
consumption during device operation. Consequently, only a small number of cyber-physical
systems deployed in the field can be tested this way and the tests to reevaluate the
device resistance to side-channel attacks cannot be easily repeated. To address these
issues, we present a design and an FPGA implementation of a built-in test for self-evaluation
of the resistance to first-order power side-channel attacks. Once our test is triggered,
the FPGA measures its own internal power-supply voltage and computes the t-test statistic
in real time. Experimental results on two different implementations of the AES-128
algorithm demonstrate that the self-evaluation test is very reliable. We believe that
this work is an important step towards the development of security sensors for the
next generation of safe and robust cyber-physical systems.

FPGA emulation is a promising approach to accelerating Network-on-Chip (NoC) modeling
which has traditionally relied on software simulators. In most early studies of FPGA-based
NoC emulators, only synthetic workloads like uniform and bit permutations were considered.
Although a set of carefully designed synthetic workloads can reveal a relatively thorough
coverage of the characteristics of the NoC under evaluation, they alone are insufficient,
especially when the NoC needs to be optimized for specific applications. In such cases,
trace-driven workloads are effective. However, there is a problem with conventional
trace-driven workloads that has been pointed out by some recent studies: the network
load and congestion may be distorted because dependencies between packets are not
considered. These studies also provide infrastructures for extending existing software
simulators to enforce dependencies between packets. Unfortunately, enforcing dependencies
between packets is not trivial in the FPGA emulation approach. Therefore, although
there are some recent FPGA-based NoC emulators supporting trace-driven workloads,
most of them ignore packet dependencies. In this paper, we first clarify the challenges
of supporting trace-driven workloads with dependencies between packets taken into
account in the FPGA emulation approach. We then propose efficient methods and architectures
to tackle these challenges and build an FPGA-based NoC emulator, which we call DNoC,
based on the proposals. Our evaluation results show that (1) on a VC707 FPGA board,
DNoC achieves an average speed of 10,753K cycles/s when emulating an 8×8 NoC with
trace data collected from full-system simulation of the PARSEC benchmark suite, which
is 274x higher than the speed reported in a recent related work on dependency-driven
trace-based NoC emulation on FPGAs; (2) Compared to BookSim, one of the most popular
NoC simulators, DNoC is 395x faster while providing the same results; (3) DNoC can
scale to a 4,096-node NoC on a VC707 board, and the size of the largest NoC depends
on only the on-chip memory capacity of the target FPGA.

Sorting is a fundamental operation in many applications such as databases, search,
and social networks. Although FPGAs have been shown very effective at sorting data
sizes that fit on chip, systems that sort larger data sets by shuffling data on and
off chip are bottlenecked by costly merge operations or data transfer time. We propose
a new technique for sorting large data sets, which uses a variant of the samplesort
algorithm on a server with a PCIe-connected FPGA. Samplesort avoids merging by randomly
sampling values to determine how to partition data into non-overlapping buckets that
can be independently sorted. The key to our design is a novel parallel multi-stage
hardware partitioner, which is a scalable high-throughput solution that greatly accelerates
the samplesort partitioning step. Using samplesort for FPGA-accelerated sorting provides
several advantages over mergesort, while also presenting a number of new challenges
that we address with cooperation between the FPGA and the software running on the
host CPU. We prototype our design using Amazon Web Services FPGA instances, which
pair a Xilinx Virtex UltraScale+ FPGA with a high-performance server. Our experiments
demonstrate that our prototype system sorts 2^30 key-value records with a speed of
7.2 GB/s, limited only by the on-board DRAM capacity and available PCIe bandwidth.
When sorting 2^30 records, our system exhibits a 37.4x speedup over the widely used
GNU parallel sort on an 8-thread state-of-the-art CPU.

K-Means is a popular clustering algorithm widely used and extensively studied in the
literature. In this paper we explore the challenges and opportunities in using low
precision input in conjunction with a standard K-Means algorithm as a way to improve
the memory bandwidth utilization on hardware accelerators. Low precision input through
quantization has become a standard technique in machine learning to reduce computational
costs and memory traffic. When applied in FPGAs, several issues need to be addressed.
First and foremost is the overhead of storing the data at different precision levels
since, depending on the training objective, different levels of precision might be
needed. Second, the FPGA design needs to accommodate varying precision without requiring
reconfiguration. To address these concerns, we propose Bit-Serial K-Means (BiS-KM),
a combination of a hybrid memory layout supporting data retrieval at any level of
precision, a novel FPGA design based on bit-serial arithmetic, and a modified K-Means
algorithm tailored to FPGAs. We have tested BiS-KM with various data sets and compared
our design with a state-of-the-art FPGA accelerator. BiS-KM achieves an almost linear
speedup as precision decreases, providing a more effective way to perform K-Means
on FPGAs.

Data movement is the dominating factor affecting performance and energy in modern
computing systems. Consequently, many algorithms have been developed to minimize the
number of I/O operations for common computing patterns. Matrix multiplication is no
exception, and lower bounds have been proven and implemented both for shared and distributed
memory systems. Reconfigurable hardware platforms are a lucrative target for I/O minimizing
algorithms, as they offer full control of memory accesses to the programmer. While
bounds developed in the context of fixed architectures still apply to these platforms,
the spatially distributed nature of their computational and memory resources requires
a decentralized approach to optimize algorithms for maximum hardware utilization.
We present a model to optimize matrix multiplication for FPGA platforms, simultaneously
targeting maximum performance and minimum off-chip data movement, within constraints
set by the hardware. We map the model to a concrete architecture using a high-level
synthesis tool, maintaining a high level of abstraction, allowing us to support arbitrary
data types, and enables maintainability and portability across FPGA devices. Kernels
generated from our architecture are shown to offer competitive performance in practice,
scaling with both compute and memory resources. We offer our design as an open source
project to encourage the open development of linear algebra and I/O minimizing algorithms
on reconfigurable hardware platforms.

Graph Convolutional Networks (GCNs) have emerged as the state-of-the-art deep learning
model for representation learning on graphs. It is challenging to accelerate training
of GCNs, due to (1) substantial and irregular data communication to propagate information
within the graph, and (2) intensive computation to propagate information along the
neural network layers. To address these challenges, we design a novel accelerator
for training GCNs on CPU-FPGA heterogeneous systems, by incorporating multiple algorithm-architecture
co-optimizations. We first analyze the computation and communication characteristics
of various GCN training algorithms, and select a subgraph-based algorithm that is
well suited for hardware execution. To optimize the feature propagation within subgraphs,
we propose a light-weight pre-processing step based on a graph theoretic approach.
Such pre-processing performed on the CPU significantly reduces the memory access requirements
and the computation to be performed on the FPGA. To accelerate the weight update in
GCN layers, we propose a systolic array based design for efficient parallelization.
We integrate the above optimizations into a complete hardware pipeline, and analyze
its load-balance and resource utilization by accurate performance modeling. We evaluate
our design on a Xilinx Alveo U200 board hosted by a 40-core Xeon server. On three
large graphs, we achieve an order of magnitude training speedup with negligible accuracy
loss, compared with state-of-the-art implementation on a multi-core platform.

Spectral-domain CNNs have been shown to be more efficient than traditional spatial
CNNs in terms of reducing computation complexity. However they come with a ‘kernel
explosion’ problem that, even after compression (pruning), imposes a high memory burden
and off-chip bandwidth requirement for kernel access. This creates a performance gap
between the potential acceleration offered by compression and actual FPGA implementation
performance, especially for low-latency CNN inference. In this paper, we develop a
principled approach to overcoming this performance gap and designing a low-latency,
low-bandwidth, spectral sparse CNN accelerator on FPGAs. First, we analyze the bandwidth-storage
tradeoff of sparse convolutional layers and locate communication bottlenecks. We then
develop a dataflow for flexibly optimizing data reuse in different layers to minimize
off-chip communication. Finally, we propose a novel scheduling algorithm to optimally
schedule the on-chip memory access of multiple sparse kernels and minimize read conflicts.
On a state-of-the-art FPGA platform, our design reduces data transfers by 42% with
DSP utilization up to 90% and achieves inference latency of 9 ms for VGG16, compared
to the baseline state-of-the-art latency of 68 ms.

All software ultimately relies on hardware functioning correctly. Hardware correctness
is becoming increasingly important due to the growing use of custom accelerators using
FPGAs to speed up applications on servers. Furthermore, the increasing complexity
of hardware also leads to ever more reliance on automation, meaning that the correctness
of synthesis tools is vital for the reliability of the hardware. This paper aims to
improve the quality of FPGA synthesis tools by introducing a method to test them automatically
using randomly generated, correct Verilog, and checking that the synthesised netlist
is always equivalent to the original design. The main contributions of this work are
twofold: firstly a method for generating random behavioural Verilog free of undefined
values, and secondly a Verilog test case reducer used to locate the cause of the bug
that was found. These are implemented in a tool called Verismith. This paper also
provides a qualitative and quantitative analysis of the bugs found in Yosys, Vivado,
XST and Quartus Prime. Every synthesis tool except Quartus Prime was found to introduce
discrepancies between the netlist and the design. In addition to that, Vivado and
a development version of Yosys were found to crash when given valid input. Using Verismith,
eleven bugs were reported to tool vendors, of which six have already been fixed.

A central task in high-level synthesis is scheduling: the allocation of operations
to clock cycles. The classic approach to scheduling is static, in which each operation
is mapped to a clock cycle at compile-time, but recent years have seen the emergence
of dynamic scheduling, in which an operation’s clock cycle is only determined at run-time.
Both approaches have their merits: static scheduling can lead to simpler circuitry
and more resource sharing, while dynamic scheduling can lead to faster hardware when
the computation has non-trivial control flow.

In this work, we seek a scheduling approach that combines the best of both worlds.
Our idea is to identify the parts of the input program where dynamic scheduling does
not bring any performance advantage and to use static scheduling on those parts. These
statically-scheduled parts are then treated as black boxes when creating a dataflow
circuit for the remainder of the program which can benefit from the flexibility of
dynamic scheduling.

An empirical evaluation on a range of applications suggests that by using this approach,
we can obtain 74% of the area savings that would be made by switching from dynamic
to static scheduling, and 135% of the performance benefits that would be made by switching
from static to dynamic scheduling.

FPGA vendors provide OpenCL software development kits for easier programmability,
with the goal of replacing the time-consuming and error-prone register-transfer level
(RTL) programming. Many studies explore optimization methods (e.g., loop unrolling,
local memory) to accelerate OpenCL programs running on FPGAs. These programs typically
follow the default OpenCL execution model, where a kernel deploys multiple work-items
arranged into work-groups. However, the default execution model is not always a good
fit for an application mapped to the FPGA architecture, which is very different from
the multithreaded architecture of GPUs, for which OpenCL was originally designed.
In this work, we identify three other execution models that can better utilize the
FPGA resources for the OpenCL applications that do not fit well into the default execution
model. These three execution models are based on two OpenCL features devised for FPGA
programming (namely, single work-item kernel and OpenCL channel). We observe that
the selection of the right execution model determines the performance upper bound
of a particular application, which can vary by two orders magnitude between the most
suitable execution model and the most unsuitable one. However, there is no way to
select the most suitable execution model other than empiricall exploring the optimization
space for the four of them, which can be prohibitive. To help FPGA programmers identify
the right execution model, we propose Boyi, a systematic framework that makes automatic
decisions by analyzing OpenCL programming patterns in an application. After finding
the right execution model with the help of Boyi, programmers can apply other conventional
optimizations to reach the performance upper bound. Our experimental evaluation shows
that Boyi can 1) accurately determine the right execution model, and 2) greatly reduce
the exploration space of conventional optimization methods.

Programming abstractions decrease the cognitive gap between program idealization and
expression. In the software domain, this high-level expressive power is achieved through
layered abstractions – virtual machines, compilers, operating systems – which translate,
at design and runtime, programmer visible code into hardware-compatible code. While
this paradigm is ideal for static, i.e., unmodifiable, hardware, several of these
abstractions break down when programming configurable hardware. State of the art hardware/software
co-design techniques (e.g., High Level Synthesis (HLS), Intermediate Fabrics) are,
for the most part, ad hoc patches to the traditional abstraction stack, applicable
only to specific toolchains or software components. In this paper, we survey current
hardware design and hardware/software co-design abstractions, from the perspective
of the design language/toolchain. We perform a systematic analysis of different design
paradigms, including HLS, Domain Specific Languages (DSL), and new-generation Hardware
Description Languages (HDL). We analyze how these paradigms differ in expressiveness,
support for hardware/software interaction, hierarchy and modularity, HDL interoperability,
and interface with the outside world.

With the technical advance of quantum computers that can solve intractable problems
for conventional computers, many of the currently used public-key cryptosystems become
vulnerable. Recently proposed post-quantum cryptography (PQC) is secure against both
classical and quantum computers, but existing embedded systems such as smart card
can not easily support the PQC algorithms due to their much larger key sizes and more
complex arithmetics. To accelerate the PQC algorithms, embedded systems have to embed
the PQC hardware blocks, which can lead to huge hardware design costs. Although High-Level
Synthesis (HLS) helps significantly reduce the design costs, current HLS frameworks
produce inefficient hardware design for the PQC algorithms in terms of area and performance.
This work analyzes common features of the PQC algorithms and proposes a new pipeline-aware
logic deduplication method in HLS. The proposed method shares commonly invoked logic
across hardware design while considering load balancing in pipeline and resolving
dynamic memory accesses. This work implements FPGA hardware design of seven PQC algorithms
in the round 2 candidates from the National Institute of Standards and Technology
(NIST) PQC standardization process. Compared to commercial HLS framework, the proposed
method achieves an area-delay-product reduction by 34.5%.

The use of parallelism has increased drastically in recent years. Parallel platforms
come in many forms: multi-core processors, embedded hybrid solutions such as multi-processor
system-on-chip with reconfigurable logic, and cloud datacenters with multi-core and
reconfigurable logic. These heterogeneous platforms can offer massive parallelism,
but it can be difficult to exploit, particularly when combining solutions constructed
with multiple architectures. To program a heterogeneous platform, a developer must
master different programming languages, tools, and APIs to program each aspect of
platform separately and then must find a means to connect them with communication
interfaces. The motivation of this work is to provide a single programming model and
framework for hardware-software stream programs on heterogeneous platforms. Our framework,
StreamBlocks, starts with a dataflow programming model for both embedded and datacenter
platforms. Dataflow programming is an alternative model of computation that captures
both data and task parallelism. We describe a compiler infrastructure for CAL dataflow
programs for hardware code generation. CAL is a dataflow programming language that
can express multiple dataflow models of computation. StreamBlocks is based on the
Tycho compiler infrastructure, which transforms each actor in a dataflow program to
an abstract machine model, called Actor Machine. Actor Machines provides a unified
model for executing actors in both hardware and software and permit our compiler extension
and backend to generate efficient FPGA code. Unlike other systems, the programming
model and compiler directly support hardware-software systems in which an FPGA functions
as a coprocessor to a CPU. This permits easy integration with existing workflows.

Designs generated by high-level synthesis (HLS) tools typically achieve a lower frequency
compared to manual RTL designs. We study the timing issues in a diverse set of nine
realistic HLS designs and observe that in most cases the frequency degradation is
related to the signal broadcast structures. In this work, we classify the common broadcast
types in HLS designs, including the data signal broadcast and two types of control
signal broadcast: the pipeline control broadcast and the synchronization signal broadcast.
We further identify several common limitations of the current HLS tools, which lead
to improper handling of the broadcasts. First, the HLS delay model does not consider
the extra delay caused by broadcasts, thus the scheduling results will be suboptimal.
To solve the issue, we implement a set of comprehensive synthetic designs and benchmark
the extra delay to calibrate the HLS delay model. Second, the HLS adopts back-pressure
signals for pipeline control, which will lead to large broadcasts. Instead, we propose
to use the skid-buffer-based pipeline control, where the back-pressure signal is removed,
and an extra skid-buffer is used for flow-control. We use dynamic programming to minimize
the area of the extra FIFO. Third, there exist redundant synchronizations among concurrent
modules that may lead to huge broadcasts. We propose methods to identify and prune
unnecessary synchronization signals. Our solutions boost the frequency of nine real-world
HLS benchmarks by 53% on average and with marginal area and latency overhead. In some
cases, the gain is more than 100 MHz.

Current High-Level Synthesis frameworks provide a productive hardware development
methodology where hardware accelerators are generated directly from high-level languages
like C/C++ or OpenCL, allowing software developers to quickly accelerate their applications.
However, the hardware generated by these frameworks is sub-optimal compared to often
hand-optimized RTL modules. A hybrid development approach would leverage the productive
software stack and hardware board support package that HLS provides but allow for
fine-grained optimization using RTL components. In this work, we introduce a new software-hardware
co-design framework that integrates OpenCL/OpenACC with RTL code enabling direct execution
on FPGAs as well as full emulation with a high-speed simulator to reduce the development
time.

The P4 language and the PISA architecture have revolutionized the field of networking.
Thanks to P4 and PISA, new networking applications and protocols can be rapidly evaluated
on high performance switches. While P4 allows the expression of a wide range of packet
processing algorithms, current programmable switch architecture limit the overall
processing flexibility. To address this shortcoming recent work have proposed to implement
PISA on FPGAs. However, little effort has been devoted to analyze whether FPGAs are
good candidates to implement PISA. In this work, we take a step back and evaluate
the micro-architecture efficiency of various PISA blocks. Using a theoretical analysis
and experiments, we demonstrate that current FPGA architecture drastically limit the
performance of a few PISA blocks. Thus, we explore two avenues to alleviate these
shortcomings. First, we identify some network applications that are well tailored
to current FPGAs. Second, to support a wider range of networking applications, we
propose modifications to the FPGA architecture which can also be of interest outside
the networking field.

The resource requirements of application-specific accelerators challenge embedded
system designers who have a tight area budget but must cover a range of possible software
kernels. We propose an early detection methodology (ReconfAST) to identify computationally
similar synthesizable kernels to build Shared Accelerators (SAs). SAs are specialized
hardware accelerators that execute very different software kernels but share the common
hardware functions between them. SAs increase the fraction of workloads covered by
specialized hardware by detecting similarities in dataflow and control flow between
seemingly very different workloads. Existing methods use either dynamic traces or
analyze register transfer level (RTL) implementations to find these similarities which
require deep knowledge of RTL and time-consuming design process.

ReconfAST leverages abstract-syntax-trees (ASTs) generated from LLVM’s-clang to discover
similar kernels among workloads. ASTs provide the right level of abstraction to detect
commonalities. ASTs are compact, unlike control and dataflow representations, but
contain extra syntax and variable node ordering that complicates workload comparison.
ReconfAST, transforms ASTs into a new clustered-ASTs (CASTs) representation, removes
unneeded nodes, and uses a regular expression to match common node configurations.
The approach is validated using MachSuite accelerator benchmarks.

On FPGAs, a good Shared Accelerator accelerates workloads by an average of 5x and
reduces the resources required for FPGA implementations: 37% FFs, 16% DSPs, and 10%
on LUTs on average over a dedicated accelerator implementation.

Prevalent hardware description languages (HDLs), e.g., Verilog and VHDL, employ register-transfer
level (RTL) as their underlying programming model. One major downside of the RTL model
is that it tightly couples design functionality with timing and device constraints.
This coupling increases code complexity and yields code that is more verbose and less
portable. High-level synthesis (HLS) tools decouple functionality from timing and
design constraints by utilizing constructs from imperative programming languages.
These constructs and their sequential semantics, however, impede construction of inherently
parallel hardware and data scheduling, which is crucial in many design use-cases.

In our work we present a novel dataflow hardware description abstraction layer as
basis for hardware design and apply it to DFiant, a Scala-embedded HDL. DFiant leverages
dataflow semantics along with modern software language features (e.g., inheritance,
polymorphism) and classic HDL traits (e.g., bit-accuracy, input/output ports) to decouple
functionality from implementation constraints. Therefore, DFiant designs are timing-agnostic
and device-agnostic and can be automatically pipelined by the DFiant compiler to meet
target performance requirements. With DFiant we demonstrate how dataflow HDL code
can be substantially more portable and compact than its equivalent RTL code, yet without
compromising its target design performance.

With the advent of Machine Learning (ML), predictive EDA tools are becoming the next
hot topic of research in the EDA community, and researchers are working on ML-based
tools to predict the performance of the EDA tool. As the designs become complex, there
is a need to start the design using higher levels of abstraction, such as High-Level
Synthesis (HLS) tools in FPGA and SoC design flows. Quick prediction of performance-related
parameters of the final design after the C-synthesis stage, can help in rapid design
closure. Even though multiple papers exist in the domain of post routing performance
prediction of HLS tools, there are no standard benchmarks available to compare the
performance and accuracy of the predictive models. In this paper, we have presented
MLSBench, a collection of around 5000 synthesizable designs written in C and C++.
We provide a methodology to generate designs with various variations from a single
design, which creates a potential for creating newer designs and enlarging the database
in the future. This is followed by analysis, and validating the generated designs
are indeed different. This allows designers to create generalized machine-learning-based
models that are not overfitted to a small dataset. We also perform statistical analysis
for measuring the design diversity by synthesizing them using Xilinx-Vivado HLS for
Zynq 7000 device series.

Design methodologies for synthesizing FPGA fabrics presented in the literature typically
employ a bottom-up approach wherein individual tiles are synthesized in isolation
and later stitched together to generate the large FPGA fabric. However, using a bottom-up
methodology to ensure fabric-level performance targets is challenging due to the lack
of a global timing view across multiple tiles spanning the FPGA fabric. While previous
works address this problem with a combination of manual buffering and floorplanning,
these additional steps introduce significant deviations from standard push-button
ASIC flows. In this paper, a top-down synthesis methodology is proposed, which eliminates
the need for floorplanning and manual buffering by providing a global timing view
of the FPGA fabric. To evaluate the proposed design methodology, we developed an FPGA
fabric generator using the Chisel hardware construction language. The fabric generator
reads in the Verilog-to-Routing architecture file, describing the user-defined FPGA
fabric, and generates the Verilog netlist and timing exceptions required to automatically
place and route the FPGA fabric in any technology node with a standard cell library.
Post layout timing analysis of placed and routed FPGA fabrics on a 28nm industrial
CMOS process demonstrates that the top-down methodology can place and route fabrics
without the need for any manual buffering or floorplanning while providing ~20% average
improvement in performance across multiple benchmark designs.

Among all the neural network specialized hardware accelerators like the Application-Specific-Integrate-Circuit(ASIC),
an FPGA accelerator stands out for its flexibility, short time-to-market, and energy
efficiency. However, when it comes to multitasking and high-speed requirements or
realtime and power-efficient scenarios (e.g., UAVs, self-driving cars, and IoT devices),
a single-board FPGA accelerator has difficulties in achieving excellent performance.
Therefore, Cloud FPGAs(Multi-FPGAs) will be a significant role in high-performance
and energy-efficient computation of CNNs for both mobile and cloud computing domains.
In this work, we propose an adaptive neural network accelerator on Cloud FPGAs, using
multi-FPGA design to satisfy multitasking and high-speed requirements or realtime
and power-efficient scenarios. We adopt the roofline model to figure out the optimal
configuration of each CNN layer. And a layer clustering algorithm and a layer sequence
detection method are proposed to transform CNN models into layer sequences for mapping
the CNN model layers efficiently to different FPGA boards. Then, we built an adaptive
CNN mapping method of Multi-FPGA chips for CNN models. Preliminary results on the
Multi-FPGAs platform demonstrate that our accelerator can improve the performance
significantly due to the adaptive mapping method.

The 2-D median filter, one of the oldest and most well-established image-filtering
techniques, still sees widespread use throughout computer vision. Despite its relative
algorithmic simplicity, accelerating the 2-D median filter via a hardware implementation
becomes increasingly challenging as the window size increases, since the resources
required grow quadratically with the window size. Previous works, in a non-FPGA context,
have shown that applying a sequence of multiple directional median filters to an image
yields results that are competitive with, and in some cases even better than, those
of a classic 2-D window median. Inspired by these approaches, we propose a novel way
of substituting a 2-D median filter on an FPGA with a sequence of directional median
filters, in our case in the pursuit of an FPGA implementation that achieves better
scalability and hardware efficiency without sacrificing accuracy. We empirically show
that the combination of three particular directional filters, in any order, achieves
this, whilst requiring quadratically fewer resources on the FPGA. Our approach allows
for much higher throughput and is easier to implement as a pipeline.

Deep learning has becoming increasingly more popular in recent years, and there are
many popular frameworks in the market accordingly, such as Caffe, TensorFlow and Pytorch.
All these frameworks natively support CPUs and GPGPUs. However, FPGAs still cannot
provide a comprehensive support by these frameworks for deep learning development,
especially for the training phase. In this paper, we firstly propose the FeCaffe,
i.e. FPGA-enabled Caffe, a hierarchical software and hardware design methodology based
on the Caffe, to enable FPGA to support CNN training features. Moreover, we provide
some benchmarks of popular CNN networks with FeCaffe, and further analysis in details
accordingly. Finally, some optimization directions including FPGA kernel design, system
pipeline, network architecture, user case application and heterogeneous platform levels,
have been proposed gradually. The result demonstrates the proposed FeCaffe can support
almost full features for training and inference respectively with high degree of design
flexibility, expansibility and reusability for deep learning development. Compared
to prior studies, our architecture can support more network and training settings
and current configuration can achieve 6.4x and 8.4x average execution time improvement
for forward and backward respectively for LeNet.

High-Level Synthesis (HLS) can achieve significant performance improvements through
effective memory partitioning and meticulous data reuse. Many modern applications,
such as medical imaging and convolutional layers in a CNN, mostly contain kernels
where iterations can be reordered freely without compromising its correctness. In
this paper, we propose an optimal micro-architecture that can be automatically implemented
for simple and iterative stencil computations that utilizes only 2 banks to achieve
fully parallel conflict memory accesses from single stage stencil kernels, while only
requiring reuse buffers of size proportional to the kernel size to achieve an II of
1, irrespectively of the stencil geometry. We demonstrate the effectiveness of our
micro-architecture by implementing it with a Kintex 7 xc7k160tg676-1 Xilinx FPGA and
testing it with several stencil-based kernels found in real-world applications. On
average, when compared with the mainstream GMP and SRC architectures our approach
achieves approximately 30- 70% reduction in hardware usage, while improving performance
by about 15%. Moreover, the number of independent memory banks required to accomplish
conflict-free data accesses have dropped by more than 30% together with some increase
in power consumption due to higher clock frequencies.

Per-flow traffic measurement has emerged as a critical but challenging task in data
center in recent years in the face of massive network traffic. Many approximate methods
have been proposed to resolve the existing resource-accuracy trade-off in per-flow
traffic measurement, one of which is the sketch-based method. However, sketches are
affected by their high computational cost and low throughput; moreover, their measurement
accuracy is hard to guarantee under the conditions of changing network bandwidth or
flow size distribution. Recently, FPGA platforms have been widely deployed in data
centers, as they demonstrate a good fit for high-speed network processing. In this
work, we propose a scalable pipelined architecture for high high-throughput per-flow
traffic measurement on FPGA. We adopts memory-friendly D-left hashing in our design,
which guarantees high space utilization that successfully addressing the challenge
of tracking high speed data stream under limit memory resource on FPGA. Comparisons
with state-of-the-art sketch-based solutions show that our design outperforms state-of-the-art
sketch-based methods in terms of throughput by over 80x.

Field-programmable gate arrays (FPGAs) have become a popular compute platform for
convolutional neural network (CNN) inference; however, the design of a CNN model and
its FPGA accelerator has been inherently sequential. A CNN is first prototyped with
no-or-little hardware awareness to attain high accuracy; subsequently, an FPGA accelerator
is tuned to that specific CNN to maximize its efficiency. Instead, we formulate a
neural architecture search (NAS) optimization problem that contains parameters from
both the CNN model and the FPGA accelerator, and we jointly search for the best CNN
model-accelerator pair that boosts accuracy and efficiency -we call this Codesign-NAS.
In this paper we focus on defining the Codesign-NAS multiobjective optimization problem,
demonstrating its effectiveness, and exploring different ways of navigating the codesign
search space. For Cifar-10 image classification, we enumerate close to 4 billion model-accelerator
pairs, and find the Pareto frontier within that large search space. Next we propose
accelerator innovations that improve the entire Pareto frontier. Finally, we compare
to ResNet on a highly-tuned accelerator, and show that using codesign, we can improve
on Cifar-100 classification accuracy by 1.8% while simultaneously increasing performance/area
by 41% in just 1000 GPU-hours of running Codesign-NAS, thus demonstrating that our
automated codesign approach is superior to sequential design of a CNN model and accelerator.

VLSI implementation of Cellular Automata (CAs) has gained importance owing to its
features which guarantee parallelism, locality and structural regularity. In this
work, we have addressed the design challenges pertaining to an implementation optimized
for speed, of tree-structured linear CA architectures on Field Programmable Gate Array
(FPGA) with built-in scan paths. Scan based design facilitates state initialization,
helps to escape from any graveyard state, or figure out faulty locations (if any)
on which the circuit is mapped. Our design automation platform generates synthesizable
circuit descriptions of tree-structured CA on FPGA, and appends scan functionality
without additional logic or speed overhead. Placement algorithms governing the map
of CA cell nodes on the FPGA slices have been proposed to ensure maximum physical
proximity among CA cells sharing neighborhood dependencies. This is done to exploit
the VLSI amenable features such as physical adjacency of the neighboring nodes participating
in the next state (NS) computation of each other. The ultimate implementation leads
to minimum spacing of linear order between CA neighbours. The NS logic of each CA
cell inclusive of scan multiplexing, owing to restricted neighborhood size, is realized
using a single Look-Up Table. Our architectures outperform behavioral implementations
realized with higher levels of design style abstraction.

Multi-Robot Exploration (MR-Exploration) that provides the location and map is a basic
task for many multi-robot applications. Recent researches introduce Convolutional
Neural Network (CNN) to critical components in MR-Exploration, like Feature-point
Extraction (FE) and Place Recognition (PR), to improve the system performance. Such
CNN-based MR-Exploration requires running multiple CNN models simultaneously, together
with complex post-processing algorithms, greatly challenges the hardware platforms,
which are usually embedded systems. Previous researches have shown that FPGA is a
good candidate for CNN processing on embedded platforms. But such accelerators usually
process different models sequentially, lacking the ability to schedule multiple tasks
at runtime. Furthermore, post-processing of CNNs in FE is also computation consuming
and becomes the system bottleneck after accelerating the CNN models. To handle such
problems, we propose an INterruptible CNN Accelerator for Multi-Robot Exploration
(INCAME) framework for rapid deployment of robot applications on FPGA. In INCAME,
we propose a virtual-instruction-based interrupt method to support multi-task on CNN
accelerators. INCAME also includes hardware modules to accelerate the post-processing
of the CNN-based components. Experimental results show that INCAME enables multi-task
scheduling on the CNN accelerator with negligible performance degradation (0.3%).
With the help of multi-task supporting and post-processing acceleration, INCAME enables
embedded FPGA to execute MR-Exploration in real time (20 fps).

Low bit quantization of neural network is required on edge devices to achieve lower
power consumption and higher performance. 8bit or binary network either consumes a
lot of resources or has accuracy degradation. Thus, a full-process hardware-friendly
quantization solution of 4A4W (activations 4bit and weights 4bit) is proposed to achieve
better accuracy/resource trade-off. It doesn’t contain any additional floating operations
and achieve accuracy comparable to full-precision. We also implement a low-precision
accelerator for CNN (LPAC) on the Xilinx FPGA, which takes full advantage of its DSP
by efficiently mapping convolutional computations. Through on-chip reassign management
and resource-saving analysis, high performance can be achieved on small chips. Our
4A4W solution achieves 1.8x higher performance than 8A8W and 2.42x increase in power
efficiency under the same resource. On ImageNet classification, the accuracy has a
gap less than 1% to full-precision in Top-5. On the human pose estimation, we achieve
261 frames per second on ZU2EG, which is 1.78x speed up compared to 8A8W and the accuracy
has only 1.62% gap to full-precision. This proves that our solution has better universality.

FPGAs have shown great potential in providing low-latency and energy-efficient solutions
for deep learning applications, especially for the deep neural network (DNN). Currently,
the majority of FPGA based DNN accelerators are designed for single-task and static-workload
applications, making it difficult to adapt to the multi-task and dynamic-workload
applications in the cloud. To meet these requirements, DNN accelerators need to support
multi-task concurrent execution and low-overhead runtime resources reconfiguration.
However, neither instruction set architecture (ISA) based nor template-based FPGA
accelerators can support both functions at the same time. In this paper, we introduce
a novel FPGA virtualization framework for ISA-based DNN accelerators in the cloud.
As for the design goals of supporting multi-task and runtime reconfiguration, we propose
a two-level instruction dispatch module and deep learning hardware resources pooling
technique at the hardware level. As for the software level, we propose a tiling-based
instruction frame package design and two-stage static-dynamic compilation. Furthermore,
we propose a history information aware scheduling algorithm for the proposed ISA-based
deep learning accelerators in the cloud scenario. According to our evaluation on Xilinx
VU9P FPGA, the proposed virtualization method achieves 1.88x to 2.20x higher throughput
and 1.36x to 1.77x lower latency against the static baseline design.

Numerous algorithmic optimization techniques have been proposed to alleviate the computational
complexity of convolutional neural networks (CNNs). However, given the broad selection
of inference accelerators, it is not obvious which approach benefits from which optimization
and to what degree. In addition, the design space is further obscured by many deployment
settings such as power and operating modes, batch sizes, as well as ill-defined measurement
methodologies. In this paper, we systematically benchmark different types of CNNs
leveraging both pruning and quantization as the most promising optimization techniques
leveraging a novel benchmarking approach. We evaluate a spectrum of FPGA implementations,
GPU, TPU and VLIW processor, for a selection of systematically pruned and quantized
neural networks (including ResNet50, GoogleNetv1, MobileNetv1, a VGG derivative, and
a multilayer perceptron) taking the full design space into account including batch
sizes, thread counts, stream sizes and operating modes, and considering power, latency,
and throughput at a specific accuracy as figure of merit. Our findings show that channel
pruning is effective across most hardware platforms, with resulting speedups directly
correlated to the reduction in compute load, while FPGAs benefit the most from quantization.
FPGAs outperform regarding latency and latency variation for the majority of CNNs,
in particular with feed-forward dataflow implementations. Finally, pruning and quantization
are orthogonal techniques and yield the majority of all optimal design points when
combined. With this benchmarking approach, both in terms of methodology and measured
results, we aim to drive more clarity in the choice of CNN implementations and optimizations.

Recently, FPGA-accelerated cloud has emerged as a new computing environment. The inclusion
of FPGAs in the cloud has created new security risks, some of which are due to circuits
exercising excessive switching activity. These power-wasting tenants can cause timing
faults in the collocated circuits or a denial-of-service attack by resetting the host
FPGA. In this work, we present the idea of populating the FPGA with voltage sensors
based on ring oscillators, to continuously monitor the core voltage fluctuations across
the entire FPGA. To implement the sensors, we do not lock any FPGA resources; instead,
we infiltrate the sensors undercover, by taking advantage of the logic and the routing
resources unused by the tenants. Additionally, we infiltrate the sensors into the
FPGA circuits after their implementation, but before their deployment on the cloud;
the tenants are thus neither aware nor affected by our voltage monitoring system.
Finally, we devise a novel metric that takes the sensor measurements to quantify the
power wasting activity in the FPGA clock regions where the sensors are infiltrated.
We use VTR benchmarks and a Xilinx Virtex-7 FPGA to test the feasibility of our approach.
Experimental results demonstrate that, using the undercover voltage sensors and our
novel metric, one can accurately locate the source of the malicious power-wasting
activity.

High Level Synthesis (HLS) tools, like the Intel FPGA SDK for OpenCL, improve hardware
design productivity and enable efficient design space exploration, by providing simple
program directives (pragmas) and/or API calls that allow hardware programmers to use
higher-level languages (like HLS-C or OpenCL). However, modern HLS tools sometimes
miss important optimizations that are necessary for high performance. In this poster,
we present a study of the tradeoffs in HLS optimizations, and the potential of a modern
HLS tool in automatically optimizing an application. We perform the study on a generic,
5-stage camera ISP pipeline using the Intel FPGA SDK for OpenCL and an Arria 10 FPGA
Dev Kit. We show that automatic optimizations in the HLS tool are valuable, achieving
up to 2.7x speedup over equivalent CPU execution. With further hand tuning, however,
we can achieve up to 36.5x speedup over CPU. We draw several specific lessons about
the effectiveness of automatic optimizations guided by simple directives and about
the nature of manual rewriting required for high performance. Finally, we conclude
that there is a gap in the current potential of HLS tools which needs to be filled
by next-gen research.

Miniaturized fluorescent calcium imaging miniscope has become a prominent technique
in monitoring the activity of a large population of neurons in vivo. However, existing
calcium image processing algorithms are developed for off-line analysis, and their
implementations on general-purpose processors are difficult to meet the real-time
processing requirement under constrained energy budget for closed-loop applications.
In this paper, we propose the CANSEE, a customized accelerator for neural signal enhancement
and extraction from calcium image in real time. The accelerator can perform the motion
correction, the calcium image enhancement, and the fluorescence tracing from up to
512 cells with less than 1-ms processing latency. We also designed the hardware that
can detect new cells based on the long short-term memory (LSTM) inference. We implemented
the accelerator on a Xilinx Ultra96 FPGA. The implementation achieves 15.8x speedup
and over 2 orders of magnitude improvement in energy efficiency compared to the evaluation
on the multi-core CPU.

Low precision data representation is important to reduce storage size and memory access
for convolutional neural networks (CNNs). Yet, existing methods have two major limitations:
(1) requiring re-training to maintain accuracy for deep CNNs, and (2) needing 16-bit
floating point or 8-bit fixed point for a good accuracy.

In this paper, we propose a low precision (8-bit) floating point (LPFP) quantization
method for FPGA-based acceleration to overcome the above limitations. Without any
re-training, LPFP finds an optimal 8-bit data representation with negligible top-1/top-5
accuracy loss (within 0.5%/0.3% in our experiments, respectively, and significantly
better than existing methods for deep CNNs). Furthermore, we implement one 8-bit LPFP
multiplication by one 4-bit multiply-adder (MAC) and one 3-bit adder, and therefore
implement four 8-bit LPFP multiplications using one DSP slice of Xilinx Kintex-7 family
(KC705 in this paper) while one DSP can implement only two 8-bit fixed point multiplications.
Experiments on six typical CNNs for inference show that on average, we improve throughput
by 64.5× over Intel i9 CPU and by 1.5× over existing FPGA accelerators. Particularly
for VGG16 and YOLO, compared to six recent FPGA accelerators, we improve average throughput
by 3.5× and 27.5× and improve average throughput per DSP by 4.1× and 5×, respectively.
To the best of our knowledge, this is the first in-depth study to simplify one multiplication
for CNN inference to one 4-bit MAC and implement four multiplications within one DSP
while maintaining comparable accuracy without any re-training.

Field Programmable Gate Array (FPGA) platform has been a popular choice for deploying
Convolutional Neural Networks (CNNs) as a result of its high parallelism and low energy
consumption. Due to the limitation of on-chip resources on a single board, FPGA clusters
become promising solutions to improve the throughput of CNNs. In this paper, we firstly
put forward strategies to optimize the resource allocation intra and inter FPGA boards.
Then we model the multi-board cluster problem and design algorithms based on knapsack
problem and dynamic programming to calculate the optimal topology of the FPGA clusters.
We also give a quantitative analysis of the inter-board data transmission bandwidth
requirement. To make our design accommodate for more situations, we provide solutions
for deploying fully connected layers and special convolution layers with large memory
requirement. Experimental results show that typical well-known CNNs with the proposed
topology of FPGA clusters could obtain a higher throughput per board than single-board
solutions and other multi-board solutions.

Over the past years, feed-forward convolutional neural networks (CNNs) have evolved
from a simple feed-forward architecture to deep and residual (skip-connection) architectures,
demonstrating increasingly higher object categorization accuracy and increasingly
better explanatory power of both neural and behavioral responses. However, from the
neuroscientist point of view, the relationship between such deep architectures and
the ventral visual pathway is incomplete. For example, current state-of-the-art CNNs
appear to be too complex (e.g., now over 100 layers for ResNet) compared with the
relatively shallow cortical hierarchy (4-8 layers). We introduce new CNNs with shallow
recurrent architectures and skip connections requiring fewer parameters. With higher
accuracy for classification, we propose an architecture for recurrent residual convolutional
neural network (R2CNN) on FPGA, which efficiently utilizes on-chip memory bandwidth.
We propose an Output-Kernel- Input-Parallel (OKIP) convolution circuit for a recurrent
residual convolution stage. We implement the inference hardware on a Xilinx ZCU104
evaluation board with high-level synthesis. Our R2CNN accelerator achieves top-5 accuracy
of 90.08% on ImageNet bench- mark, which has higher accuracy than conventional FPGA
implementations.

Computational neuroscience uses models to study the brain. The Hodgkin-Huxley (HH)
model, and its extensions, is one of the most powerful, biophysically meaningful models
currently used. The high experimental value of the (extended) Hodgkin-Huxley (eHH)
models comes at the cost of steep computational requirements. Consequently, for larger
networks, neuroscientists either opt for simpler models, losing neuro-computational
features, or use high-performance computing systems. The eHH models can be efficiently
implemented as a dataflow application on a FPGA-based architecture. The state-of-the-art
FPGA-based implementations have proven to be time-consuming because of the long-duration
synthesis requirements. We have developed flexHH, a flexible hardware library, compatible
with a widely used neuron-model description format, implementing five FPGA-accelerated
and parameterizable variants of eHH models (standard HH with optional extensions:
custom ion-gates, gap junctions, and/or multiple cell compartments). Therefore, flexHH
is a crucial step towards high-flexibility and high-performance FPGA-based simulations,
eschewing the penalty of re-engineering and re-synthesis, dismissing the need for
an engineer. In terms of performance, flexHH achieves a speedup of 1,065x against
NEURON, the simulator standard in computational neuroscience, and speedups between
8x-20x against sequential C. Furthermore, flexHH is faster per simulation step compared
to other HPC technologies, provides 65% or better performance density (in FLOPS/LUT)
compared to related works, and only shows a marginal performance drop in real-time
simulations.

This poster presents a novel cross-layer-pipelined Convolutional Neural Network accelerator
architecture, and network compiler, that make use of precision minimization and parameter
pruning to fit ResNet-50 entirely into on-chip memory on a Stratix 10 2800 FPGA. By
statically partitioning the hardware across each of the layers in the network, our
architecture enables full DSP utilization and reduces the soft logic per DSP ratio
by roughly 4x over prior work on sparse CNN accelerators for FPGAs. This high DSP
utilization, a frequency of 420MHz, and skipping zero weights enable our architecture
to execute a sparse ResNet-50 model at a batch size of 1 at 3300 images/s, which is
nearly 3x higher throughput than NVIDIA’s fastest machine learning targeted GPU, the
V100. We also present a network compiler and a flexible hardware interface that make
it easy to add support for new types of neural networks, and to optimize these networks
for FPGAs with different on-chip resources.

Hardware acceleration of deep learning (DL) systems has been increasingly studied
to achieve desirable performance and energy efficiency. The FPGA strikes a balance
between high energy efficiency and fast development cycle and therefore is widely
used as a DNN accelerator. However, there exists an architecture-layout mismatch in
the current designs, which introduces scalability and flexibility issues, leading
to irregular routing and resource imbalance problems. To address these limitations,
in this work, we propose FTDL, an FPGA-tailored architecture with a parameterized
and hierarchical hardware that is adaptive to different FPGA devices. FTDL has the
following novelties: (i) At the architecture level, FTDL consists of Tiled Processing
Elements (TPE) and super blocks, to achieve a near-to-theoretical digital signal processing
(DSP) operating-frequency of 650 MHz. More importantly, FTDL is configurable and delivers
good scalability, i.e., the timing is stabilized even when the design is scaled-up
to 100% resource utilization for different deep learning systems. (ii) In workload
compilation, FTDL provides a compiler that manages to map the DL workloads to the
architecture level in an optimal manner. Experimental results show that for most benchmark
layers in MLPerf, FTDL achieves an over 80% hardware efficiency.

With Moore’s Law coming to an end, hardware specialization and systems on chips are
providing new opportunities for continuing performance scaling while reducing the
energy cost of computation. However, the current hardware design methodologies require
significant engineering efforts and domain expertise, making the design process unscalable.
More importantly, hardware specialization presents a unique challenge for a much tighter
software and hardware co-design environment to exploit domain-specific optimizations
and design efficiency. In this work, we introduce Cash, a single-source hardware-software
co-design framework for rapid SoC prototyping and accelerators research. Cash leverages
the unique efficiency and generative attributes of Modern C++ to provide a unified
development environment, aiming at closing the architecture research methodology gap.
The Cash framework introduces new co-design programming abstractions that enable seamless
integration with existing software from architecture research simulators to high-level
synthesis.

Stream computing is a suitable approach to improve both performance and power efficiency
of numerical computations with FPGAs. To achieve further performance gain, temporal
and spatial parallelism were exploited: the first one deepens and the latter duplicates
pipelines of streamed computation cores. These two types of parallelism were previously
evaluated with Arria 10 FPGA. However, it has not been verified if they are also effective
for the latest FPGA, Stratix 10, which has a larger amount of logic elements (i.e.,
2.4X of Arria 10) and is equipped with a new feature to improve the maximum clock
frequency (i.e., HyperFlex architecture). To show the scalability for such state-of-the-art
FPGAs, in this paper, we firstly implemented a streamed fluid simulation accelerator
with both parallelism types for Stratix 10. We then thoroughly evaluated it by obtaining
computational performance (FLOPS), power efficiency (FLOPS/W), resource utilization,
and maximum clock frequency (Fmax). From the results, we found that this implementation
excessively used DSP blocks due to inefficient mapping of floating-point operations,
which reduced Fmax and the number of pipelined cores. To improve the scalability,
we optimized the implementation to reduce the DSP block usage by utilizing a Multiply-Add
function in a single DSP block. As a result, the optimized fluid simulation achieves
1.06 TFLOPS and 12.6 GFLOPS/W, which is 1.36X and 1.24X higher than the non-optimized
version, respectively. Moreover, we estimate that the fluid simulation with Stratix
10 could outperform GPU-based implementation with Tesla V100 by optimizing it for
HyperFlex architecture.

Routing is one of the most time-consuming steps in the FPGA synthesis flow. Existing
works have described several ways to accelerate the routing process. The partitioning-based
parallel routing technique that leverages the high-performance computing of multi-core
processors are gaining popularity recently. Specifically, those parallel routers partition
nets to regions by nets’ bounding boxes, followed by a parallel routing procedure.
Nets can be split up into source-sink connections that share wire segments as much
as possible. In order to exploit more parallelism by a finer granularity in both spatial
partitioning and routing, a connection-aware routing bounding box model is introduced
in this work. We first explore in detail to show that connection-aware partitioning
using the new routing bounding boxes enables the parallel routing to perform better
runtime efficiency than the existing net-based partitioning by analyzing the workloads
of parallel routers. It reduces the connections spanning more than one region and
exploits more parallelism. The large heterogeneous Titan23 designs and a detailed
representation of the Stratix IV FPGA are used for benchmarking. Experimental results
show that the parallel FPGA router is faster when using our connection-aware partitioning
than using the existing net-based partitioning, while achieving similar quality of
routing results in terms of the wirelength and critical path delay. The connection-aware
routing bounding box model is easy to be embedded into other existing parallel routers
and further enables them to be faster.

With the advent of AI and machine learning as the highest profile FPGA applications,
INT8 performance is currently one of the key benchmarking metrics. In current devices,
INT8 multipliers must be extracted from higher precision multipliers. Recently, we
reported the implementation of a mixed DSP Block and soft logic design, with 22,400
INT8 multipliers, and a system clock rate of 416MHz, on the Intel Stratix 10 2800
chip.

In this paper we demonstrate alternate techniques for integer multiplier construction
to better balance the resource types on current FPGAs – logic, memory, and DSP – to
make a significant improvement in the multiplier, and therefore the dot product, density.
We further extend these techniques to 8 bit signed-magnitude (SM) 1.7 representation,
which can further improve arithmetic density by using the logic and memory resources
more flexibly. We describe variable composition dot product structures, which can
be assembled in a scalable 2D systolic array. In one example, we report a design containing
32,768 SM1.7 multipliers, with a clock rate of 432MHz, giving a system performance
of over 28 TOPs. Our INT8 densities are improved by up to 30% over the earlier work
– we show one design with 28,800 INT8 multipliers. In all cases, enough device resources
are left free and accessible to implement a full application level design.

With tremendous economic and technological ramifications, hardware security has become
an increasingly more critical design metric for FPGA-based logic design. In this work,
we focus on countermeasures against power side-channel attacks in any reconfigurable
computing system implemented with modern FPGA fabric. We design and implement a novel
countermeasure technique called Time-Fracturing (TF) to fend off side-channel-based
information leakage, which proves to be both hardware-efficient and minimally invasive.
To validate its effectiveness, we have applied our TF technique to an FPGA-based AES128
encryption core. Our experimental results have shown an increase of more than 50 times,
when compared to its unprotected baseline, in its attack difficulty measured by the
number of traces required to extract the secret key. Furthermore, our approach is
orthogonal to existing methods, thus having the potential to be integrated in the
future for a multi-variate defense mechanism.

Accurate timing characterization of FPGA routing resources, i.e. wires and switches,
is critical to achieving high quality of results from FPGA routing tools. Although
the composition and connectivity of the routing resources are easily extracted from
an FPGA’s architecture, post-layout timing characterization of the FPGA’s wires and
switches (NOT the design being mapped onto the FPGA) with EDA tools is a challenging
task due to the large quantity of combinational loops (cycles in the routing graph).
Likewise, the use of EDA tools is severely limited when constructing new FPGA architectures.
This work addresses the challenge by proposing an algorithm to construct cycle-free
FPGA routing graphs. A cycle-free FPGA routing graph is achieved by logically ordering
wires and intelligently removing or rearranging a small fraction of the switch block
connections in order to break cycles. The proposed approach enables constraining the
timing of all routing resources, which is otherwise impossible due to the combinational
loops. This technique can be applied to post-layout static timing analysis (STA) of
existing FPGAs, significantly reducing the complexity and improving the accuracy of
the analysis. In addition, this cycle-free approach can be adopted when designing
new FPGAs, transforming costly hand layout into an automated step compatible with
commercial ASIC EDA tools.

Logic replication is often necessary to improve speed of emulation for systems employing
field programmable gate arrays (FPGAs), since design sizes are large enough requiring
partitioning to fit a design into multiple (boards of) FPGAs. In this paper, we propose
a polynomial time algorithm for combinational logic replication that ensures delay
optimality for directed acyclic graphs and reduces overhead due to look-up table (LUT)
and cut resources. The algorithm is further extended to consider combinational loops,
often yielding delay optimal results. Experimental results on industrial designs show,
on an average, 44%, 33%, and 33% reduction in overhead due to cut, LUT costs, and
runtimes, respectively, compared to existing heuristics, thus demonstrating the efficiency
of the algorithm.

Q-Table based Reinforcement Learning (QRL) is a class of widely used algorithms in
AI that work by successively improving the estimates of Q values — quality of state-action
pairs, stored in a table. They significantly outperform Neural Network based techniques
when the state space is tractable. Fast learning for AI applications in several domains
(e.g. robotics), with tractable ‘mid-sized’ Q-tables, still necessitates performing
substantial rapid updates. State-of-the-art FPGA implementations of QRL do not scale
with the increasing Q-Table state space, thus are not efficient for such applications.
In this work, we develop a novel FPGA implementation of QRL, scalable to large state
spaces and facilitating a large class of AI applications. Our pipelined architecture
provides higher throughput while using significantly fewer on-chip resources and thereby
supports a variety of action selection policies that covers Q-Learning and variations
of bandit algorithms. Possible dependencies caused by consecutive Q value updates
are handled, allowing the design to process one Q-sample every clock cycle. Additionally,
we provide the first known FPGA implementation of the SARSA (State-Action-Reward-State-Action)
algorithm. We evaluate our architecture for Q-Learning and SARSA algorithms and show
that our designs achieve a high throughput of up to 180 million Q samples per second.

Designing efficient hardware for accelerating machine learning (ML) applications is
a major challenge. Rapid changing algorithms and network architectures in this field
make FPGA based designs an attractive solution. But the generic building blocks available
in current FPGAs (ALMs/CLBs, DSP blocks) limit the acceleration that can be achieved.
We propose a modification to the current FPGA architecture that makes FPGAs specialized
for ML applications. Specifically, we propose adding hard matrix multiplier blocks
(matmuls) into the FPGA fabric. These matmuls are implemented using systolic arrays
of MACs (Multiply-And-Accumulate) and can be connected using programmable direct interconnect
between neighboring matmuls to make larger systolic matrix multipliers. We explore
various matmul sizes (4x4x4, 8x8x8, 16x16x16, 32x32x32) and various strategies to
place these blocks on the FPGA (clustered, surround, columnar). We recommend 4x4x4
matmul blocks with columnar placement after studying tradeoffs between area, frequency,
fragmentation and channel width. Experimental results and analytical evaluation reveal
that providing matmuls in an FPGA speeds up state-of-the-art neural networks (Resnet50,
GNMT, Transformer, Minigo) by ~2.5x on average, compared to a DSP-heavy FPGA with
equal number of MACs. Therefore, FPGAs with hard matrix multipliers can be used to
design faster, more area (and hence, power) efficient hardware accelerators for ML
applications, compared to current FPGAs, at the cost of reducing the flexibility of
the FPGA for other applications. A matmul-heavy FPGA fabric could be a part of bigger
FPGA, the rest of which can have general programmable logic, or fully ML-specific
FPGAs with matmuls could be created.

FPGA platforms are widely used for application acceleration. Although a number of
high-level design frameworks exist, application and performance portability across
different platforms remain challenging. To address the above problem, we propose an
API design for high-level development tools to separate platform-dependent code from
the remaining application design. Additionally, we propose design guidelines to assist
with performance portability. To demonstrate our techniques, a large-scale application,
originally developed for an Intel Stratix-V FPGA is ported to several new Xilinx Virtex
UltraScale+ systems. The accelerated application, developed in a high-level framework,
is rapidly moved onto the new platforms with minimal changes. The original, unmodified
kernel code delivers a 1.74x speedup due to increased clock frequency on the new platform.
Subsequently, the application is further optimised to make use of the additional resources
available on the larger Ultrascale+ FPGAs, guided by a simple analytical performance
model. This results in an additional performance increase of up to 7.4x. Using the
presented framework, we demonstrate rapid deployment of the same application across
a number of different platforms that leverage the same FPGA family but differ in their
low-level implementation details and the available peripherals. As a result, the same
application code supports five different platforms: Maxeler MAX5C DFE, Amazon EC2
F1, Xilinx Alveo U200, U250 and the original Intel Stratix-V accelerator card, with
performance close to what is theoretically achievable for each of these platforms.

Approximate computing (AC) aims to achieve energy-efficiency in digital systems by
sacrificing the computational accuracy of an application. Memory-intensive applications,
in which a large amount of data is processed to reach a meaningful conclusion, are
the primary target. Systems for such applications consists of a large pool of compute-unit
and sizeable on-chip memory. The total energy consumption for such applications is
often dominated by the on-chip memory. We, therefore, focus on improving the energy
efficiency of the on-chip memory by appropriately scaling down its supply voltage.

In this paper, we propose a memory allocation technique for FPGA-based accelerators
to improve accuracy and energy consumption for such memory-intensive applications.
Unlike state-of-the-art, our technique focusses on the BRAM of the FPGA. Since an
application consists of both critical and non-critical data and is required to treat
them accordingly to maintain good computational accuracy, we thereby use LUTRAM of
FPGA to realize the reliable memory, whereas BRAM operating at a lower voltage is
considered as the unreliable one. First, we introduce a compiler pre-processor to
annotate the arrays of an application as critical and non-critical ones. Afterward,
we employ an exploration heuristic to select an optimal point of the reliable and
unreliable memories for the application without incurring run-time as well as energy
consumption based on pre-characterize memory power. Experimental results on various
signal and image processing applications reveal that the proposed memory allocation
heuristic improves the accuracy from 13.0% to 73.2% along with 0.77x energy savings
while incurring 1.12x circuit area.

Phylogenetics study the evolutionary history of a collection of organisms based on
observed heritable molecular traits, finding practical application in a wide range
of domains, from conservation biology and epidemiology, to forensics and drug development.
A fundamental computational kernel to evaluate evolutionary histories, also referred
to as phylogenies, is the Phylogenetic Likelihood Function (PLF), which dominates
the total execution time (by up to 95%) of widely used maximum-likelihood phylogenetic
methods. Numerous efforts to boost PLF performance over the years mostly focused on
accelerating computation; since the PLF is a data-intensive, memory-bound operation,
performance remains limited by data movement. In this work, we employ near-memory
computation units (NMUs) within a FPGA-based computing environment with disaggregated
memory to alleviate the data movement problem and improve performance and energy efficiency
when inferring large-scale phylogenies. NMUs were deployed on a multi-FPGA emulation
platform for the IBM dReDBox disaggregated datacenter prototype. We find that performance
and power efficiency improves by an order of magnitude when NMUs compute on local
data that reside on the same server tray. This is achieved through an efficient data-allocation
scheme that minimizes inter-tray data transfers (remote-data movement) when computing
the PLF. More specifically, we observe up to 22x better FLOPS performance and 13x
higher power efficiency (FLOPS/Watt) over the more traditional, accelerator-as-a-coprocessor
model, which requires explicit remote-data transfers between disaggregated memory
modules and accelerator units.

The FPGA circuit design usually adopts full-custom design method, it indicates that
it is difficult to design and optimize an FPGA manually. So, we present FPTLOPT (FPGA
Transistor-Level Optimization Tool) which supports a more complex FPGA architecture
called general routing matrix (GRM) architecture, and also has higher-accuracy and
higher-speed than COFFE [1]. To fit a more complex FPGA architecture, we use the regular
matching method to automatically extract the circuits type and build the circuits
netlist; To get the higher-accuracy, we predict the layout area by area model we build,
then we precisely predict the layout post simulation delay by load model we build;
To get the higher-speed, we devise the variable range greedy algorithm, to expanding
range automatically. We also provide equalization kernel multi-thread acceleration
that can change the thread number according to the current CPU hardware environment.
The experimental results illustrate that FPTLOPT supports the optimization of GRM
architecture and build the key sub-circuit netlist. Also, the area prediction is by
maximum of 43%, the delay get from delay prediction is 28% more precise than the ones
in COFFE. Besides, quickly gets the optimal transistor sizing results for different
optimization objectives. For the same circuit, the optimization speed is 19.96 times
faster than COFFE.

CAD exploration is important for designing FPGA interconnect topologies. It includes
two steps: first, design a model with some parameters that can express as much architecture
space. Second, use CAD flow to analyze the described interconnect architecture. In
this paper, we present a new interconnect model, named INTB (Interconnect Block).
At a logical position, one INTB is adopted to represent all related routing resources
and hierarchical parameters are designed to simplify description. Compared with existing
CB-SB model, INTB model can support more interconnect features of modern FPGA, such
as various types of wire segment and complex connections. These features can improve
FPGA routing ability. For the application of INTB model, two modifications are made
in CAD flow: one is generation of routing resource graph (RRG). A tile-based method
is proposed to generate RRG from parameters. The other is cost computing during routing
process. Two strategies are applied respectively for cost estimation of short and
curve wire segment, which do not exist in CB-SB model. INTB model and CAD improvement
are implemented in VTR 8.0. The experiments consist of two parts. First, INTB model
is adopted to re-describe CB-SB architectures to verify its description capacity.
After CAD flow, average difference of routing area and timing between two models is
about 4% and 5%. Second, INTB model is used to explore architecture space with modern
FPGA features. Experimental results show obvious performance enhancement, over 10%
in some benchmarks.

Long Short-Term Memory (LSTM) has been widely adopted in tasks with sequence data,
such as speech recognition and language modeling. LSTM brought significant accuracy
improvement by introducing additional parameters to Recurrent Neural Network (RNN).
However, increasing number of parameters and computations also led to inefficiency
in computing LSTM on edge devices with limited on-chip memory size and DRAM bandwidth.
In order to reduce the latency and energy of LSTM computations, there has been a pressing
need for model compression schemes and suitable hardware accelerators. In this paper,
we first propose the Fixed Nonzero-ratio Viterbi-based Pruning, which can reduce the
memory footprint of LSTM models by 96% with negligible accuracy loss. By applying
additional constraints on the distribution of surviving weights in Viterbi-based Pruning,
the proposed pruning scheme mitigates the load-imbalance problem and thereby increases
the processing engine utilization rate. Then, we propose the V-LSTM, an efficient
sparse LSTM accelerator based on the proposed pruning scheme. High compression ratio
of the proposed pruning scheme allows the proposed accelerator to achieve 24.9% lower
per-sample latency than that of state-of-the-art accelerators. The proposed accelerator
is implemented on Xilinx VC-709 FPGA evaluation board running at 200MHz for evaluation.

This paper presents a system-level co-simulation and co-verification workflow to ease
the transition from a software-only procedure, executed in a General Purpose processor,
to the integration of a custom hardware accelerator developed in a Hardware Description
Language (HDL).

We propose a tool which enables Dynamic Binary Modification to decouple the development
of the hardware accelerator from the software-only application to be accelerated.
It provides support for rapid iterative exploration and functional verification of
hardware designs while keeping the unmodified software application as a reference.
DBHI is able to instrument an application and inject compiled hardware. It allows
progressive migration from application source code, to non-synthesizable HDL, and
to synthesizable HDL. At the same time, it preserves cycle-accurate/bit-accurate results,
and provides run-time visibility of the internal data buffers for debugging purposes.
Foreign architecture emulation overhead during development is avoided, and early integration
with peripherals in the target System-on-Chip is possible.

The proposed design flow was evaluated on executions of hardware simulations on x86-64
and Arm. DBHI was developed from existing off-the-shelf tools, and we evaluated it
on multiple architectures, however, the technique is not tied to any specific architecture.

Hyperconvergence is a software-centric architecture which has disrupted the datacenter
industry in a dramatic way by bringing the disparate areas of compute, storage and
networking into a single system. A hyperconverged system allows the integrated …

Machine learning has been used to improve the predictability of different physical
design problems, such as timing, clock tree synthesis and routing, but not for legalization.
Predicting the outcome of legalization can be helpful to guide incremental …

As the wide adoption of FinFET technology in mass production, dynamic power becomes
the bottleneck to achieving low power. Therefore, clock power reduction is crucial
in modern IC design. Register clustering can effectively save clock power because
of …

The layouts of analog/mixed-signal (AMS) integrated circuits (ICs) are dramatically
different from their digital counterparts. AMS circuit layouts usually include a variety
of devices, including transistors, capacitors, resistors, and inductors. A …

Modern circuit designs often contain standard cells of different row heights to meet
various design requirements. Due to the higher interference among heterogeneous cell
structures, the legalization problem for mixed-cell-height standard cells becomes
…

The continued rapid growth of data, along with advances in Artificial Intelligence
(AI) to extract knowledge from such data, is reshaping the computing ecosystem landscape.
With AI becoming an essential part of almost every end-user application, our …

Recent technical challenges have forced the industry to explore options beyond the
conventional “one size fits all” CPU scalar processing solution. Very large vector
processing (DSP, GPU) solves some problems, but it runs into traditional scaling …

Large-scale graph analytics has gained importance due to emergence of new applications
in different contexts such as web, social networks, and computational biology. It
is known that typical CPU/GPU implementations for sparse graph applications cannot
…

In this paper, we propose a routing flow for nets within a standard cell that generates
layout of standard cells without any design rule violations. Design rules, density
rules for metal fill, and pin-access requirements are modeled via Boolean formulas
…

Optical Networks-on-Chip (ONoCs) are a promising solution for high-performance multi-core
integration with better latency and bandwidth than traditional Electrical NoCs. Wavelength-routed
ONoCs (WRONoCs) offer yet additional performance guarantees. …

Monolithic three-dimensional~(3D) integration enables stacking multiple ultra-thin
silicon tiers in a single package, thereby providing smaller footprint area, shorter
wirelength, higher performance, and lower power consumption than conventional planar
…

Routability diagnosis has increasingly become the bottleneck in detailed routing for
sub-10nm technology due to the limited tracks, high density, and complex design rules. The
conventional ways to examine the routability of detailed routing are ILP- and …

As integrated circuit manufacturing becomes increasingly global and the availability
of domestically produced advanced transistor nodes shrinks, security vulnerabilities
within the supply chain become a significant issue for IC defense applications. In
…

This paper presents a formal (machine readable) declarative language developed for
the specific reason of modeling physical design process rules of any complexity. Case
studies are presented on synthetic as well as industry known design rules of simple
…

Electromigration (EM) is seen as a growing problem in recent and upcoming technology
nodes, and affects a wider variety of wires (e.g., power grid, clock/signal nets),
circuits (e.g., digital, analog, mixed-signal), and systems (e.g., mobile, server,
…

Deep learning (DL) has achieved tremendous success in computer vision, natural language
processing and gaming. Would DL help push physical design toward a more intelligent
paradigm to meet the post-Moore era design automation challenges? We will discuss
…

Multiple patterning lithography (MPL) divides a layout into several masks and manufactures
them by a series of exposure and etching steps. As technology advances, MPL is still
indispensable because of its cost effectiveness and hybrid lithography …

Advanced driver assistance systems (ADAS), autonomous functions, and connected applications
bring a revolution to automotive systems, but they also make automotive design, especially
software and electronics, more complex than ever. The complexity …

Having solved the data integration problem, we discuss how convergence of 4 technology
vectors, namely Big Data, Artificial Intelligence, Cloud Computing, and Internet of
Things (IoT) has, for the first time, enabled us to solve a class of problems …

This talk discusses some of the design challenges posed by cyber-physical system security
at different abstraction layers, from algorithm design to the realization of trusted
hardware platforms. We introduce two design problems, namely, detecting sensor …

The list of Professor Alberto Sangiovanni-Vincentelli’s research contributions is
astounding in length and breadth, yet does not entirely capture what this author believes
is his true genius. In so many areas of computer-aided design, Sangiovanni-…

We first present historical view on the techniques for two-level and multi-level logic
optimizations, and discuss the practical issues with respect to them. Then the techniques
for sequential optimizations are briefly reviewed. Based on them, a new …

This paper reflects on the design challenges posed by cyber-physical systems, what
distinguishes cyber-physical system design from large-scale integrated circuit design,
and what could be the opportunities for the design automation community. The paper
…

The article is a reflection onmy journey during the development of the EDA field,
from its early days to its explosive growth and present maturity. The two special
issues of the Solid State Circuit Society Magazine “Corsi e Ricorsi: Alberto Sangiovanni
…

Discovery, invention, and design are all about models. When we say “Joseph Priestly
discovered oxygen in 1774,” we do not mean that Priestly dug up a canister of oxygen,
recognized it as something new, and released it, for the first time, into the air.
…

Over the past decade, spurred by advances in mobile computing, there has been a fundamental
shift in computing needs of consumer applications. There has been an industry-wide
transition from highly CPU-centric to a peripheral-centric, connectivity and …

Recent work has established Lagrangian relaxation (LR) based gate sizing as state-of-the-art
providing the best power reduction with low run time. Gate sizing has limited potential
to reduce the power when the timing constraints are tight. By adjusting …

Statistical circuit simulation is exhibiting increasing importance for memory circuits
under process variation. It is challenging to accurately estimate the extremely low
failure probability as it becomes a high-dimensional and multi-failure-region …

Detailed routing becomes the most complicated and runtime consuming stage in the physical
design flow as technology nodes advance. Due to the inaccessibility of advanced routing
rules and industrial designs, it is hard to conduct detailed routing …

Modern smartphone display system come equipped with powerful GPU’s capable of rendering
advanced 2D and 3D graphics. These GPU’s make up a significant portion of the system
power profile due to the high resolution and framerate of smartphone display. …

Ternary Content-Addressable Memory (TCAM) is widely used in networking routers, fully
associative caches, search engines, etc. While the conventional SRAM-based TCAM suffers
from the poor scalability, the emerging nonvolatile memories (NVM, i.e., MRAM, …

The recent interest in emerging interconnect technologies is bringing the issue of
a proper EDA support for them to the forefront, so to tackle the design complexity.
A relevant case study is provided by wavelength-routed optical NoCs (WRONoCs), which
…

Lexicographic Boolean satisfiability (LEXSAT) is a variation of the Boolean satisfiability
problem (SAT). Given a variable order, LEXSAT finds a satisfying assignment whose
integer value under the given variable order is minimum (maximum) among all …

Threshold logic circuits gain increasing attention due to their feasible realization
with emerging technologies and strong bind to neural network applications. In this
paper, for logic synthesis we formulate the fundamental operation of collapsing …

Traditionally, floating gate (flash) transistors have been used exclusively to implement
non-volatile memory in its various forms. Recently, we showed that flash transistors
can be used to implement digital circuits as well. In this paper, we present …

As VLSI technology shrinks to fewer tracks per standard cell, e.g., from 10-track
to 7.5-track libraries (and lesser for 7nm), there has been a rapid increase in the
usage of multiple-row cells like two- and three-row flip-flops, buffers, etc., for
…

This paper proposes a powerful new technique called “OWARU”¹ that re-places and re-sizes multiple gates simultaneously to improve the most critical
paths of a design. In essence, it is an incremental timing-driven placement technique
integrated with …

In this paper, we propose a 2-dimensional dynamic programming (DP) based detailed
placement algorithm for modern FPGAs for wirelength and timing optimization. By tuning
a control parameter, our algorithm can perform fast heuristic or exact optimization.
…

Non-volatile memories (NVMs) such as Spin-Transfer Torque RAM (STTRAM) have drawn
significant attention due to complete elimination of bitcell leakage. In addition
to the plethora of benefits such as density, non-volatility, low-power and high speed,
…

Proliferation of electronics and their increasing connectivity pose formidable challenges
for information security. At the most fundamental level, nanostructures and nanomaterials
offer an unprecedented opportunity to introduce new approaches to …

With the recent advancement of multilayer convolutional neural networks (CNN), deep
learning has achieved amazing success in many areas, especially in visual content
understanding and classification. To improve the performance and energy-efficiency
of …

The rapid development of deep learning are enabling a plenty of novel applications
such as image and speech recognition for embedded systems, robotics or smart wearable
devices. However, typical deep learning models like deep convolutional neural …

Sparse matrix-vector multiplication (SpMV) is an important computational kernel in
many applications. For performance improvement, software libraries designated for
SpMV computation have been introduced, e.g., MKL library for CPUs and cuSPARSE library …

The phenomenon of metal-insulator-transition (MIT) in strongly correlated oxides,
such as NbO₂, have shown the oscillation behavior in recent experiments. In this work, the MIT
based two-terminal device is proposed as a compact oscillation neuron for …

This paper presents a new transient electro-thermal (ET) simulation method for fast
3D chip-level analysis of power electronics with field solver accuracy. The metallization
stacks are meshed and solved with 3D field solver using nonlinear temperature-…

Tensors are a multi-linear generalization of matrices to their d-way counterparts, and are receiving intense interest recently due to their natural
representation of high-dimensional data and the availability of fast tensor decomposition
algorithms. …

In this paper, a novel Asymptotic Probability Approximation (APA) method is proposed
to estimate the overall rare probability of correlated failure events for complex
circuits containing a large number of replicated cells (e.g., SRAM bit-cells). The
key …

We present Duplex random tree search, an algorithm to optimize performance metrics
of analog and mixed signal circuits. Duplex determines the optimal design, the Pareto
set and the sensitivity of circuit’s performance metrics to its parameters. We …

Clock network power reduction is critical in modern SoC designs. Application of flop trays (i.e., multi-bit flip-flops) can significantly reduce the number of sinks in a clock
network, and thus reduce the number of clock buffers, clock wirelength, and …

We address the problem of incorporating RC delay constraints into global routing.
In contrast to the usual global routing approach that focuses on minimizing net length
while obeying constraints given by other tools such as layer assignments, our method
…

Escape routing for Printed Circuit Boards (PCBs) is an important problem arising from
modern packaging with large numbers of densely spaced pins, such as BGAs. Single-layer
escape routing has been well-studied, but large, dense BGAs often require …

The integrated fan-out (InFO) wafer-level chip-scale package (WLCSP) s an emerging
packaging technology, which typically consists of multiple redistribution layers (RDLs)
for signal redistributions among multiple chips. There is still no published work
…

The value of semiconductor-based systems continues to increase rapidly especially
when considering the cost associated with building it. As such, Moore’s Law has become
a law associated broadly with value growth instead of pure performance growth. While
…

Staying at the forefront of research, or in the top tier product market requires circuit
innovation as a key differentiation. We are entering an era where more than Moore
is becoming increasingly evident, not only because of the physical limitations of
…

CMOS scaling so far enabled simultaneous system throughput scaling by concurrent improvements
in delay, power, and area with thanks to Moore’s law. CMOS scaling becomes more difficult
with the limits of interconnect and increasing wafer cost. It is …

Over the past decade, “Moore’s Law” has become increasingly well-understood as being
a law of “value scaling”: success of new electronics- and semiconductor-based products
depends on improved cost-efficiency, utility, and value. Design Automation (DA) …

The advancing of reverse engineering techniques has complicated the efforts in intellectual
property protection. Proactive methods have been developed recently, among which layout-level
IC camouflaging is the leading example. However, existing …

Integrated circuit (IC) camouflaging is a layout-level technique that thwarts reverse
engineering attacks on ICs by introducing camouflaged cells that look alike, but can
implement one of many possible Boolean functions. Existing camouflaging techniques
…

The globalization of the semiconductor foundry business poses grave risks in terms
of intellectual property (IP) protection, especially for critical applications. Over
the past few years, several techniques have been proposed that allow manufacturing
of …

Streaming architectures are a popular choice for data intensive application due to
their high throughput requirements. When assembling components for a streaming application,
it is often necessary to build translation blocks between them to match the …

To realize high throughput out of a relatively low bandwidth, memory partitioning
algorithms have been proposed to separate data arrays into multiple memory banks,
from which multiple data can be accessed in parallel. However, previous partitioning
…

In this paper, a new approach to the problem of allocating multi-bit flip-flops for
data storage is presented. Previous approaches divide the allocation problem into
two separate steps: (i) placing single-bit flip-flops under circuit timing constraints
…

Automotive platforms today run hundreds of millions of lines of software code implementing
a large number of different control applications spanning across safety-critical functionality
to driver assistance and comfort-related functions. While such …

The development of automotive electronics and software systems is often associated
with high costs due to their multi-domain nature (including control engineering, electronics,
hydraulics, mechanics, etc). The involvement of these different disciplines …

Today’s automotive industry is making a bold move to equip vehicles with intelligent
driver assistance features. A modern automobile is now equipped with a powerful computing
platform to run multiple machine learning algorithms for environment …

Next-generation autonomous and semi-autonomous vehicles will not only precept the
environment with their own sensors, but also communicate with other vehicles and surrounding
infrastructures for vehicle safety and transportation efficiency. The design, …

The CAD Contest at ICCAD is a challenging, multi-month competition, focusing on advanced,
real-world problems in the field of Electronic Design Automation (EDA). In its fifth
year, the 2016 CAD Contest at ICCAD attracted 135 teams from 11 regions/…

Injecting faults into designs is a way to qualify a verification environment. To improve
the performance of a qualifying process, we need to remove identical faults. The problem
will provide some faulty design cases; the contestants must identify all …

Boolean Matching is significant to industry applications, such as library binding,
synthesis, engineer change order, and hardware Trojan detection. Instead of basic
Boolean matching, Non-exact Projective NPNP Boolean Matching allows to match two designs
…

Layout pattern classification has been utilized in recent years in integrated circuit
design towards various goals such as design space analysis, design rule generation,
and systematic yield optimization. There is a need for open source or academic …

Recently, there have been a slew of design automation contests and released benchmarks.
ISPD place & route contests, DAC placement contests, timing analysis contests at TAU
and CAD contests at ICCAD are good examples in the past and more of new contests …

We present a novel type of Trojan trigger targeted at the field-programmable gate
array (FPGA) design flow. Traditional triggers base on rare events, such as rare values
or sequences. While in most cases these trigger circuits are able to hide a Trojan
…

A hardware Trojan (HT) detection method is presented that is based on measuring and
detecting small systematic changes in path delays introduced by capacitive loading
effects or series inserted gates of HTs. The path delays are measured using a high
…

Physical unclonable functions (PUFs) utilize manufacturing ariations of circuit elements
to produce unpredictable response to any challenge vector. The attack on PUF aims
to predict the PUF response to all challenge vectors while only a small number of
…

Conventional silicon physical unclonable function (PUF) extracts fingerprints from
transistor’s analog attributes, which are vulnerable to environmental and operational
variations. Recently, digitalized PUF prototypes have emerged to overcome the …

With the continuous shrinking of technology nodes, lithography hotspot detection and
elimination in the physical verification phase is of great value. Recently machine
learning and pattern matching based methods have been extensively studied to overcome
…

1D gridded design is one of the most promising solutions that can enable the scaling
to 10nm technology node and beyond. Line-end cuts are needed to fabricate 1D layouts, where
two techniques are available to resolve the conflicts between cuts: cut …

The directed self-assembly (DSA) technology for next-generation lithography has been
shown its great potential for fabricating highly dense via patterns and cut masks
in the sub-5 nm technology node and beyond. However, DSA via and cut optimizations
…

Two-dimensional (2D) directed self-assembly (DSA) is an emerging lithography for the
5 nm process node and beyond that can substantially increase design flexibility in
critical routing layers and reduce the number of cuts for better yield. The state-of-…

Verification is a critical task in the development of correct computing systems. Simulation
remains the predominantly used technique to identify design flaws, due to its scalability.
However, simulation intrinsically suffers from low functional coverage,…

Ensuring the correctness of SystemC virtual prototypes is indispensable. For such
models, existing symbolic simulation approaches are based on interpreting their behavior.
In this paper we propose a major enhancement called Compiled Symbolic Simulation (…

We propose an exact algorithm to model-free diagnosis with an application to fault
localization in digital circuits. We assume that a faulty circuit and a correctness
specification, e.g., in terms of an un-optimized reference circuit, are available.
Our …

This paper presents a hierarchical framework to model, analyze, and estimate digital
design vulnerability to soft errors due to Single Event Transients (SETs). A new SET
propagation model is proposed. This model simultaneously includes the impact of …

In 3D packages top-die power delivery is a not only limited by back-end of line (technology
scaling), but also by the TSV integration scheme, the stacking method and the microbump
current-carrying capability. The microbump structure and its …

Due to the increasing fabrication and design complexity with new process nodes, the
cost per transistor trend originally identified in Moore’s Law is slowing when using
traditional integration methods. However, emerging die-level integration …

The Network-on-Chip (NoC) paradigm has emerged as an enabler for integrating a large
number of embedded cores in a single die. Three-dimensional (3D) integration, a breakthrough
technology to achieve “More Moore and More Than Moore,” provides numerous …

Three-dimensional (3D) integration using through-silicon vias (TSVs) promises higher
integration levels in a single package, keeping pace with Moore’s law. Despite the
promise and benefits offered by 3D integration, testing remains a major obstacle that
…

Measurement-Based Probabilistic Timing Analysis (MBPTA) derives WCET estimates for
tasks running on processors comprising high-performance features such as caches. MBPTA’s
correct application requires the system to exhibit certain timing properties, …

As the number of cores increases, cache-based memory hierarchy is becoming a major
problem in terms of the scalability and energy consumption. Software-managed scratchpad
memories (SPM) is a scalable alternative to caches, but the benefit comes at the …

Integrated GPUs have become an indispensable component of mobile processors due to
the increasing popularity of graphics applications. The GPU frequency is a key factor
both in application throughput and mobile processor power consumption under graphics
…

Fault tolerance (FT) is essential in many Internet of Things (IoT) applications, in
particular in the domains such as medical devices and automotive systems where a single
fault in the system can lead to serious consequences. Non-volatile memory (NVM), …

Device miniaturization due to technology scaling has made manufacturing variability
and aging more significant, and lower supply voltage makes circuits sensitive to dynamic
environmental fluctuation. These may shorten the time to failure (TTF) of …

Adaptive Supply Voltage (ASV) is a power-efficient approach to achieving resilience
against process variation and circuit aging. Fine-grained ASV offers further power-efficiency
gains, but entails relatively complex control circuit, which has not been …

FPGA routing is a well studied problem. Basic point-to-point routing of nets on FPGA
fabrics can be done optimally using well known shortest path algorithms like Dijkstra’s
and A-star. Practical rip-up and reroute algorithms like PathFinder have been …

FPGA packing and placement without routability consideration could lead to unroutable
results for high-utilization designs. Conventional FPGA packing and placement approaches
are shown to have severe difficulties to yield good routability. In this paper,…

As the complexity and scale of FPGA circuits grows, resolving routing congestion becomes
more important in FPGA placement. In this paper, we propose a routability-driven placement
algorithm for large-scale heterogeneous FPGAs. Our proposed algorithm …

Traditional FPGA flows that wait until the routing stage to tackle congestion are
quickly becoming less effective. This is due to the increasing size and complexity
of FPGA architectures and the designs targeted for them. In this paper, we present
two …

Dynamic power management has become essential for low power designs and systems. Whether
intentionally or unintentionally, these power reduction techniques and corresponding
management schemes can impact the hardware reliability and system resiliency in …

In this article, we propose a new dynamic reliability management (DRM) techniques
at the system level for emerging low power dark silicon manycore microprocessors operating
in near-threshold region. We mainly consider the electromigration (EM) failures. …

Energy constrained systems become the cornerstone of emerging energy harvested or
battery-limited applications in Internet of Thing (IoT) platforms. A promising approach
is to operate at near threshold voltage ranges, which can significantly reduce …

Drones, also referred to as unmanned aerial vehicles (UAVs), are recently expanding
their field of usage beyond military surveillance and tactical applications. Commercial
drone delivery service is one of the promising applications in the near future, …

Flexible systems that can conform to any shape are desirable for wearable applications.
Over the past decade, there have been tremendous advances in the domain of flexible
electronics which enabled printing of devices, such as sensors on a flexible …

Additive Manufacturing (AM) uses Cyber-Physical Systems (CPS) (e.g., 3D Printers)
that are vulnerable to kinetic cyber-attacks. Kinetic cyber-attacks cause physical
damage to the system from the cyber domain. In AM, kinetic cyber-attacks are realized
by …

Human-centered Internet-of-Things (IoT) applications utilize computational algorithms
such as machine learning and signal processing techniques to infer knowledge about
important events such as physical activities and medical complications. The …

There are plentiful attempts for increasing the efficiency, generality and optimality
of the Design Space Exploration (DSE) algorithms for resource allocation problems
of distributed embedded systems. Most contemporary approaches formulate DSE as an
…

Iterative Stencil Loops (ISLs) are a specific class of algorithms of great importance
for their substantial presence in a lot of industrial and scientific computing applications,
such as in numerical methods for solving partial differential equation — …

Recent breakthroughs in deep neural networks have led to the proliferation of its
use in image and speech applications. Conventional deep neural networks (DNNs) are
fully-connected multi-layer networks with hundreds or thousands of neurons in each
…

While SystemC models provide a promising solution to the complex problem of HW/SW
co-design within the system-on-chip paradigm, such requires a detailed annotation
of transaction level energy and performance data within the model. While this data
can be …

This paper presents an architectural-space exploration methodology for designing approximate
multipliers. Unlike state-of-the-art, our methodology generates various design points
by adapting three key parameters: (1) different types of elementary …

Artificial neural networks (NN) have shown a significant promise in difficult tasks
like image classification or speech recognition. Even well-optimized hardware implementations
of digital NNs show significant power consumption. It is mainly due to non-…

Synthesis tools for approximate sequential circuits require the ability to quickly,
efficiently, and automatically characterize and bound the errors produced by the circuits.
Previous approaches to characterize errors in approximate sequential circuits …

Approximation circuits offer superior performance (speed and area) compared to traditional
circuits at the cost of computational accuracy. The accuracy of the results in approximation
circuits is evaluated based on several error metrics such as worst-…

This paper discusses the possible role of formal verification techniques in system-level
design flows. It is argued that the role of formal verification techniques should
not be limited to “bug hunting” alone. Instead, formal technology should be …

Formal techniques seem to be a way to cope with the exploding complexity of functional
safety analysis. Here, the overall fault propagation probability to a certain safety-point
in the design must be analyzed. As a consequence, the careful verification …

Large battery packs composed of Lithium-Ion cells are continuously gaining in importance
due to their applications in Electric Vehicles (EVs) and smart energy grids. To ensure
maximum lifetime, safety and performance of the battery pack, complex …

In this paper we study power, performance, and cost (PPC) tradeoffs for 2-tier, gate-level,
full-chip GDS monolithic 3D ICs (M3D) built using a foundry-grade 7nm bulk FinFET
technology. We first develop highly-accurate wafer and die cost models for 2D …

Dummy fill insertion is widely applied to significantly improve the planarity of topographic
patterns for chemical mechanical polishing process in VLSI manufacture. However, these
dummies will lead to additional parasitic capacitance and deteriorate the …

We consider the general problem of the efficient and accurate determination of the
yield of an integrated circuit, through electrical circuit level simulation, under
variability constraints due to the manufacturing process. We demonstrate the …

Split manufacturing is a technique that allows manufacturing the transistor-level
and lower metal layers of an IC at a high-end, untrusted foundry, while manufacturing
only the higher metal layers at a smaller, trusted foundry. Using split manufacturing
…

Today many design houses must outsource their design fabrication to a third party
which is often an overseas foundry. Split-fabrication is proposed for combining the
FEOL capabilities of an advanced but untrusted foundry with the BEOL capabilities
of a …

We introduce a machine learning approach for distinguishing between integrated circuits
fabricated in a ratified facility and circuits originating from an unknown or undesired
source based on parametric measurements. Unlike earlier approaches, which …

Computer systems research is often inhibited by the availability of memory designs.
Existing Process Design Kits (PDKs) frequently lack memory compilers, while expensive
commercial solutions only provide memory models with immutable cells, limited …

To access sensitive information, some recent advanced attacks have been successful
in exploiting implicit flows in a program in which sensitive data affects the control
path and in turn affects other data. To track the sensitive data through implicit
…

Secure hardware design is a challenging task that goes far beyond ensuring functional
correctness. Important design properties such as non-interference cannot be verified
on functional circuit models due to the lack of essential information (e.g., …

Providing efficient protection against energy consumption based side channel attacks
(SCAs) for block ciphers is a relevant topic for the research community, as current
overheads are in the 100x range. Unprofiled SCAs exploit information leakage from
…

Neuromorphic architectures are widely used in many applications for advanced data
processing, and often implements proprietary algorithms. In this work, we prevent
an attacker with physical access from learning the proprietary algorithm implemented
by …

Timing macro-modeling captures the timing characteristics of a circuit in a compact
form for use in a hierarchical timing environment. At the same time, statistical timing
provides coverage of the impact from variability sources with the goal of …

TinySPICE was a SPICE simulator on GPU developed to achieve dramatic speedups in statistical
simulations of small nonlinear circuits, such as standard cell designs and SRAMs.
While TinySPICE can perform circuit simulations much faster than traditional …

In static timing analysis, clock-to-q delays of flip-flops are considered as constants.
Setup times and hold times are characterized separately and also used as constants.
The characterized delays, setup times and hold times, are applied in timing …

Simulation and verification of the on-die power delivery network (PDN) is one of the
key steps in the design of integrated circuits (ICs). With the very large sizes of
modern grids, verification of PDNs has become very expensive and a host of techniques
…

Stochastic logic performs computation on data represented by random bit streams. The
representation allows complex arithmetic to be performed with very simple logic, but
it suffers from high latency and poor precision. Furthermore, the results are …

Paper-based digital microfluidic biochips (P-DMFBs) have recently emerged as a promising
low-cost and fast-responsive platform for biochemical assays. In P-DMFBs, electrodes
and control lines are printed on a piece of photo paper using inkjet printer …

Artificial neural networks have gone through a recent rise in popularity, achieving
state-of-the-art results in various fields, including image classification, speech
recognition, and automated control. Both the performance and computational complexity
…

A digital microfluidic biochip (DMFB) is an attractive technology platform for automating
laboratory procedures in biochemistry. However, today’s DMFBs suffer from several
limitations: (i) constraints on droplet size and the inability to vary droplet …

Smart grid, managed by intelligent devices, have demonstrated great potentials to
help residential customers to optimally schedule and manage the appliances’ energy
consumption. Due to the fine-grained power consumption information collected by smart
…

How to tolerate fault is a fundamental requirement to the designs of many cyber-physical
systems. Devices or sensors might have different requirements on their levels of reliability
and/or timely services in the composition of a cyber-physical system. …

Petroleum Cyber-Physical System (CPS) marks the beginning of a new chapter of the
oil and gas industry. Combining vast computational power with intelligent Computer
Aided Design (CAD) algorithms, petroleum CPS is capable of precisely modeling the
flow …

Modern smart surveillance systems can not only record the monitored environment but
also identify the targeted objects and detect anomaly activities. These advanced functions
are often facilitated by deep neural networks, achieving very high accuracy …

Due to technology scaling, electromigration (EM) signoff has become increasingly difficult,
mainly due to the use of inaccurate methods for EM assessment, such as the empirical
Black’s model. In this paper, we present a novel approach for EM checking …

Power and thermal issues are the main constraints for highperformance multi-core systems.
As the current technology of choice, FinFET is observed to have lower delay under
higher temperature in super-threshold voltage region, an effect called …

In this paper, we propose a current waveform estimation algorithm for signal lines
without the necessity of SPICE simulation. Unlike previous methods, we do not use
function fitting or compute the effective capacitance. Instead, the proposed algorithm
…

As VLSI technology features are pushed to the limit with every generation and with
the introduction of new materials and increased current densities to satisfy the performance
demands, Electromigration (EM) is projected to be a key reliability issue for …

Energy-efficient processing of large matrices for big-data applications using hardware
acceleration is an intense area of research. Sketching of large matrices into their
lower-dimensional representations is an effective strategy. For the first time, …

Neural encoder is one of the key components in neuromorphic computing systems, whereby
sensory information is transformed into spike coded trains. The design of temporal
encoder has attracted a widespread attention in the field of neuromorphic computing
…

In previous literatures, many approaches use ring oscillators or other process monitors
to correlate the chip’s maximum operating frequency (F_max). But none of them focus on the placement of these on-chip process monitors (OPMs)
on a chip. The placement …

System-level validation is the most challenging phase of design verification. A common
methodology in this context entails simulating the design under validation in lockstep
with a high-level golden model, while comparing the architectural state of the …

The STT-RAM (Spin-Transfer Torque Magnetic RAM) technology is a promising candidate
for cache memory because of its high density, low standy-power, and non-volatility.
As technology scales, especially under 40nm technology node, the read disturbance
…

Recent propositions of diverse In-Memory Computing platforms have shown a promising
alternative to classical Von Neumann computing models. Significant benefits, in terms
of energy-efficiency and performance, are reported for in-memory arithmetic …

Driven by recent advances in resistive random-access memory (RRAM), there have been
growing interests in exploring alternative computing concept, i.e., in-memory processing,
to address the classical von Neumann bottlenecks. Despite of their great …

Numerous research efforts are targeting new devices that could continue performance
scaling trends associated with Moore’s Law and/or accomplish computational tasks with
less energy. One such device is the ferroelectric FET (FeFET), which offers the …

Power Capping techniques are used to restrict power consumption of computer systems
to a thermally safe limit. Current many-core systems employ dynamic voltage and frequency
scaling (DVFS), power gating (PG) and scheduling methods as actuators for power …

Thermal analysis is crucial for determining the propagation of heat and tracking the
formation of hot spots in advanced integrated circuit technologies. At the core of
the thermal analysis for integrated circuits is the numerical solution of the heat
…

While near threshold design space provides a promising approach towards energy-efficient
computing, it is plagued by sub-optimal performance. Application characteristics and
hardware non-idealities of conventional architectures (optimized for the …

Single-ISA heterogeneous mobile processors integrate low-power and power-hungry CPU
cores together to combine energy efficiency with high performance. While running computationally
demanding applications, current power management and scheduling …

This paper describes a general framework for transforming a sequential program into
a network of processes, which are then converted to hardware accelerators through
high level synthesis. Also proposed is a complementing technique for performing static
…

Coarse-Grained Reconfigurable Architecture (CGRA) is a promising architecture with
high performance, high power-efficiency and attraction of flexibility. The compute-intensive
parts of an application (e.g. loops) are often mapped onto CGRA for …

RDF databases naturally map to a graph representation and employ languages, such as
SPARQL, that implements queries as graph pattern matching routines. Graph methods
exhibit an irregular behavior: they present unpredictable, fine-grained data accesses,
…

In this paper, we develop tier partitioning strategy to mitigate back-end-of-line
(BEOL) interconnect delay degradation and cost issues in monolithic 3D ICs (M3D).
First, we study the routing overhead and delay degradation caused by tungsten BEOL
…

Monolithic 3D IC (M3D) can continue to improve power, performance, area and cost beyond
traditional Moore’s law scaling limitations by leveraging the third-dimension and
fine-grained monolithic inter-tier vias (MIVs). Several recent studies present …

Three-dimensional integrated circuits (3D ICs) offer significant improvements over
two-dimensional circuits in several aspects. Classic 3D floorplanning algorithm places
each module at one single die. However, power consumption and wirelength of a 3D IC
…

While previous decades have witnessed impressive accomplishments in the design and
realization of conventional computing devices, physical boundaries and cost restrictions
led to an increasing interest in alternative technologies (often referred to as …

We present an outline of the field of Multilevel Design Understanding by first defining
and motivating the related problems, and then describing the key issues which must
be addressed in future research.

The Third International Workshop on Overlay Architectures for FPGAs (OLAF) is held
in Monterey, California, USA, on Feburary 22, 2017 and co-located with FPGA 2017:
The 25th ACM/SIGDA International Symposium on Field Programmable Gate Arrays. The
main …

Deep learning has garnered significant visibility recently as an Artificial Intelligence
(AI) paradigm, with success in wide ranging applications such as image and speech
recognition, natural language understanding, self-driving cars, and game playing (…

Current-generation Deep Neural Networks (DNNs), such as AlexNet and VGG, rely heavily
on dense floating-point matrix multiplication (GEMM), which maps well to GPUs (regular
parallelism, high TFLOP/s). Because of this, GPUs are widely used for …

Convolutional neural networks (CNN) are the current stateof-the-art for many computer
vision tasks. CNNs outperform older methods in accuracy, but require vast amounts
of computation and memory. As a result, existing CNN applications are typically run
…

OpenCL FPGA has recently gained great popularity with emerging needs for workload
acceleration such as Convolutional Neural Network (CNN), which is the most popular
deep learning architecture in the domain of computer vision. While OpenCL enhances
the …

We present a novel mechanism to accelerate state-of-art Convolutional Neural Networks
(CNNs) on CPU-FPGA platform with coherent shared memory. First, we exploit Fast Fourier
Transform (FFT) and Overlap-and-Add (OaA) to reduce the computational …

As convolution layers contribute most operations in convolutional neural network (CNN)
algorithms, an effective convolution acceleration scheme significantly affects the
efficiency and performance of a hardware CNN accelerator. Convolution in CNNs …

Convolutional neural nets (CNNs) have become a practical means to perform vision tasks,
particularly in the area of image classification. FPGAs are well known to be able
to perform convolutions efficiently, however, most recent efforts to run CNNs on …

Research has shown that convolutional neural networks contain significant redundancy,
and high classification accuracy can be obtained even when weights and activations
are reduced from floating point to binary values. In this paper, we present FINN,
a …

Long Short-Term Memory (LSTM) is widely used in speech recognition. In order to achieve
higher prediction accuracy, machine learning scientists have built increasingly larger
models. Such large model is both computation intensive and memory intensive. …

How should we perform component-specific adaptation for FPGAs? Prior work has demonstrated
that the negative effects of variation can be largely mitigated using complete knowledge
of device characteristics and full per-FPGA CAD flow. However, the cost …

Interconnect synthesis tools ease the burden on the designer by automatically generating
and optimizing communication hardware. In this paper we propose a novel capability
for FPGA interconnect synthesis tools that further simplifies the designer’s …

FPGAs are increasingly popular as application-specific accelerators because they lead
to a good balance between flexibility and energy efficiency, compared to CPUs and
ASICs. However, the long routing time imposes a barrier on FPGA computing, which …

While academic FPGA architecture exploration tools have become sufficiently advanced
to enable a wide variety of explorations and optimizations on soft fabric and outing,
support for Block RAM (BRAM) has been very limited. In this paper, we present …

Memory systems play a key role in the performance of FPGA applications. As FPGA deployments
move towards design entry points that are more serial, memory latency has become a
serious design consideration. For these applications, memory network …

The And-Inverter Cone has been introduced as an alternative logic element to the look-up
table in FPGAs, since it improves their performance and resource utilization. However,
further analysis of the AIC design showed that it suffers from the delay …

We design a 120-core 94MHz MIPS processor FPGA over-lay interconnected with a lightweight
message-passing fabric that fits on a Stratix V GX FPGA (5SGXEA7N2F45C2). We use silicon-tested
RTL source code for the microAptiv MIPS processor made available …

Modern FPGA synthesis tools typically apply a predetermined sequence of logic optimizations
on the input logic network before carrying out technology mapping. While the “known
recipes” of logic transformations often lead to improved mapping results, …

Mainstream FPGA CAD tools provide an extensive collection of optimization options
that have a significant impact on the quality of the final design. These options together
create an enormous and complex design space that cannot effectively be explored …

Ever greater amounts of computing and storage are happening remotely in the cloud,
and it is estimated that spending on public cloud services will grow by over 19%/year
to $140B in 2019. Besides commodity processors, network and storage infrastructure,
…

Lock-free algorithms, in which threads synchronise not via coarse-grained mutual exclusion
but via fine-grained atomic operations (‘atomics’), have been shown empirically to
be the fastest class of multi-threaded algorithms in the realm of conventional …

Recent years have seen an increased deployment of FPGAs as programmable accelerators
for improving the performance and energy efficiency of compute-intensive applications.
A well-known “secret sauce” of achieving highly efficient FPGA acceleration is to
…

Current pipelining approach in high-level synthesis (HLS) achieves high performance
for applications with regular and statically analyzable memory access patterns. However,
it cannot effectively handle infrequent data-dependent structural and data …

High-level synthesis (HLS) enables designing at a higher level of abstraction to effectively
cope with design complexity of emerging applications on modern programmable system-on-chip
(SoC). While HLS continues to evolve with a growing set of algorithms,…

Packet processing systems increasingly need larger rulesets to satisfy the needs of
deep-network intrusion prevention and cluster computing. FPGA-based implementations
of packet processing systems have been proposed but their use of on-chip memory …

Large graph processing has gained great attention in recent years due to its broad
applicability from machine learning to social science. Large real-world graphs, however,
are inherently difficult to process efficiently, not only due to their large …

The performance of large-scale graph processing suffers from challenges including
poor locality, lack of scalability, random access pattern, and heavy data conflicts.
Some characteristics of FPGA make it a promising solution to accelerate various …

Many applications that operate on large graphs can be intuitively parallelized by
executing a large number of the graph operations concurrently and as transactions
to deal with potential conflicts. However, large numbers of operations occurring …

We present a framework for creating network FPGA clusters in a heterogeneous cloud
data center. The FPGA clusters are created using a logical kernel description describing
how a group of FPGA kernels are to be connected (independent of which FPGA these …

An indispensable part of our modern life is scientific computing which is used in
large-scale high-performance systems as well as in low-power smart cyber-physical
systems. Hence, accelerators for scientific computing need to be fast and energy …

Secure Function Evaluation (SFE) has received considerable attention recently due
to the massive collection and mining of personal data over the Internet, but large
computational costs still render it impractical. In this paper, we leverage hardware
…

The increasing computational power enables various new applications that are runtime
prohibitive before. FPGA is one of such computational power with both reconfigurability
and energy efficiency. In this paper, we demonstrate the feasibility of …

With the advent of several accurate and sophisticated statistical algorithms and pipelines
for DNA sequence analysis, it is becoming increasingly possible to translate raw sequencing
data into biologically meaningful information for further clinical …

This work measures the performance and power consumption gap between the current generation
of low power FPGAs and low power microprocessors (microcontrollers) through an implementation
of the Canny edge detection algorithm. In particular, the algorithm …

This poster presents a data-centric reconfigurable architecture, which is enabled
by emerging non-volatile memory, i.e., RRAM. Compared to the heterogeneous architecture
of commercial FPGAs, it is inherently a homogeneous architecture comprising of a …

Iterative stencil algorithms find applications in a wide range of domains. FPGAs have
long been adopted for computation acceleration due to its advantages of dedicated
hardware design. Hence, FPGAs are a compelling alternative for executing iterative
…

With the rapid growth of data scale, data analysis applications start to meet the
performance bottleneck, and thus requiring the aid of hardware acceleration. At the
same time, Field Programmable Gate Arrays (FPGAs), known for their high customizability
…

Thermal management is one of the key concerns in modern high power density chips.
A variety of thermal cooling techniques that have been in use in industrial applications
are now also being applied to integrated circuits. In this work, we explore the …

Many of the key stages in the traditional FPGA CAD flow require substantial amounts
of computational effort. Moreover, due to limited overlap among individual stages,
poor decisions made in earlier stages will often adversely affect the quality of …

In high-performance applications, such as quantum physics and positron emission tomography,
precise coincidence detection is of central importance: The quality of the reconstructed
images depends on the accuracy with which the underlying system detects …

Streaming HPC applications are data intensive and have widespread use in various fields
(e.g., Computational Fluid Dynamics and Bioinformatics). These applications consist
of different processing kernels where each kernel performs a specific computation
…

Implementing an accurate and fast activation function with low cost is a crucial aspect
to the implementation of Deep Neural Networks (DNNs) on FPGAs. We propose a high accuracy
approximation approach for the hyperbolic tangent activation function of …

Snort and Bro are Deep Packet Inspection systems which express complex rules with
regular expressions. Before performing a regular expression search, these applications
apply a filter to select which regular expressions must be searched. One way to …

There have been ample successful examples of applying Xilinx Vivado’s “function-to-module”
high-level synthesis (HLS) where the subject is algorithmic in nature. In this work,
we carried out a design study to assess the effectiveness of applying Vivado-…

Component based design is one of the preferred methods to tackle system complexity,
and reduce costs and time-to-market. Major parts of the system design and IC production
are outsourced to facilities distributed across the globe, thus opening the door …

The financial market server in exchanges aims to maintain the order books and provide
real time market data feeds to traders. Low-latency processing is in a great demand
in financial trading. Although software solutions provide the flexibility to …

High-Level Synthesis (HLS) has been widely recognized and accepted as an efficient
compilation process targeting FPGAs for algorithm evaluation and product prototyping.
However, the massively parallel memory access demands and the extremely expensive
…

A pre-trained convolutional deep neural network (CNN) is a feed-forward computation
perspective, which is widely used for the embedded systems, requires high power-and-area
efficiency. This paper realizes a binarized CNN which treats only binary 2-…

FPGA-based hardware accelerator for convolutional neural networks (CNNs) has obtained
great attentions due to its higher energy efficiency than GPUs. However, it has been
a challenge for FPGA-based solutions to achieve a higher throughput than GPU …

To efficiently process a tremendous amount of data, today’s big data applications
tend to distribute the datasets into multiple partitions, such that each partition
can be fit into memory and be processed by a separate core/server in parallel. Meanwhile,…

Large-scale convolutional neural network (CNN), conceptually mimicking the operational
principle of visual perception in human brain, has been widely applied to tackle many
challenging computer vision and artificial intelligence applications. …

In recent years, Convolutional Neural Networks (ConvNets) have become the state-of-the-art
in several Artificial Intelligence tasks. Across the range of applications, the performance
needs vary significantly, from high-throughput image recognition to …

Magnetic Resonance Imaging (MRI) is widely used in medical diagnostics. Sampling of
MRI data on Cartesian grids allows efficient computation of the Inverse Discrete Fourier
Transform for image reconstruction using the Inverse Fast Fourier Transform (…

Convolutional neural networks (CNNs) are used to solve many challenging machine learning
problems. These networks typically use convolutional layers for feature extraction
and fully-connected layers to perform classification using those features. …

The proliferation of high-throughput sequencing machines allows for the rapid generation
of billions of short nucleotide fragments in a short period. This massive amount of
sequence data can quickly overwhelm today’s storage and compute infrastructure. …

Despite the considerable improvements in the quality of HLS tools, they still require
the designer’s manual optimizations and tweaks to generate efficient results, which
negates the HLS design productivity gains. Majority of designer interventions lead
…

Although there is explosive growth of theoretical research on cognitive radio, the
real-time platform for cognitive radio is progressing at a low pace. Researchers expect
fast prototyping their designs with appropriate wireless platforms to precisely …

FPGAs have been used as accelerators in a wide variety of domains such as learning,
search, genomics, signal processing, compression, analytics and so on. In recent years,
the availability of tools and flows such as high-level synthesis has made it even
…

Data flow graph (DFG) mapping is critical for the compiling of spatial programmable
architecture, where compilation time is a key factor for both time-to-market requirement
and mapping successful rate. Inspired from the great progress made in tree …

In this presentation we show that side-channels arising from micro-architecture of
SoCFPGAs could be a security risk. We present a FPGA trojan based on OpenCL which
performs cache-timing attacks through the accelerator coherency port (ACP) of a SoCFPGA.
…

Library based design and IP reuses have been previously proposed to speed up the synthesis
of large-scale FPGA designs. However, existing methods result in large area wastage
due to the module size difference and the waste area inside each module. In …

We present a design-time tool, EASTA, that combines the feature of reconfigurability
in FPGAs and Dynamic Frequency Scaling to realize an efficient multiprocessing scheduler
on a single-FPGA system. Multiple deadlines, reconvergent nodes, flow …

Chip security has long been the domain of smart cards. These microcontrollers are
specifically designed to thwart many different attacks in order to deliver typical
security functions as payment cards, electronic passports, and access cards. With
the …

Implementation of high performance multi-camera / multi-sensor imaging systems that
are required to produce real-time video output pose a large number of unique challenges
to conventional digital design based on general-purpose processors or GPUs. In …

Today, it would be difficult to find medical device technology that does not critically
depend on computer software. Network connectivity and wireless communication has transformed
the delivery of patient care. The technology often enables patients to …

Intelligent things, medical devices, vehicles and factories, all part of cyberphysical
systems, will only be secure if we can build devices that can perform the mathematically
demanding cryptographic operations in an efficient way. Unfortunately, many …

Many lattice-based cryptosystems are based on the security of the Ring learning with
errors (Ring-LWE) problem. The most critical and computationally intensive operation
of these Ring-LWE based cryptosystems is polynomial multiplication. In this paper,
…

Untrusted third-parties are found throughout the integrated circuit (IC) design flow
resulting in potential threats in IC reliability and security. Threats include IC
counterfeiting, intellectual property (IP) theft, IC overproduction, and the insertion
…

This paper presents the design of a non-volatile register file using cells made of
a SRAM and a Programmable Metallization Cell (PMC). The proposed cell is a symmetric
8T2P (8-transistors, 2PMC) design; it utilizes three control lines to ensure the …

Physical unclonable functions (PUFs) leverage minute silicon process variations to
produce device-tied secret keys. The energy and area costs of creating keys from PUFs
can far exceed the costs of the basic PUF circuits alone. Minimizing the end-to-end
…

Discrete Fourier Transformation (DFT)/Fast Fourier Transformation (FFT) are the widely
used techniques in numerous modern signal processing applications. In general, because
of their inherent multiplication-intensive characteristics, the hardware …

Cryptographic systems are vulnerable to random errors and injected faults. Soft errors
can inadvertently happen in critical cryptographic modules and attackers can inject
faults into systems to retrieve the embedded secret. Different schemes have been …

As chip multiprocessors (CMPs) are becoming more susceptible to process variation,
crosstalk, and hard and soft errors, emerging threats from rogue employees in a compromised
foundry are creating new vulnerabilities that could undermine the integrity of …

The Monte-Carlo method is the method of choice for accurate yield estimation. Standard
Monte-Carlo methods suffer from a huge computational burden even though they are very
accurate. Recently a Monte-Carlo method was proposed for the parametric yield …

Almost 90% of the data available today was created within the last couple of years,
thus Big Data set processing is of utmost importance. Many solutions have been investigated
to increase processing speed and memory capacity, however I/O bottleneck is …

Wearable personal health monitoring systems can offer a cost effective solution for
human healthcare. These systems must provide both highly accurate, secured and quick
processing and delivery of vast amount of data. In addition, wearable biomedical …

New hardware security threats are identified in emerging three-dimensional (3D) integrated
circuits (ICs) and potential countermeasures are introduced. Trigger and payload mechanisms
for future 3D hardware Trojans are predicted. Furthermore, a novel, …

The network delay upper-bound analysis problem is of fundamental importance to real-time
applications in Network-on-Chip (NoC). In the paper, we revisit a state-of-the-art
analysis model for real-time communication in wormhole NoC with priority-based …

Due to near-threshold computing nowadays, voltage emergency is threatening our design
margins very seriously. Noise sensors are inserted in order to prevent various integrity
issues from happening during runtime. In this work, we use a new technique …

In modern VLSI design, manufacturing yield and chip performance are seriously affected
by via failure. Redundant via insertion is an effective technique recommended by foundries
to deal with the via failure. However, due to the extreme scaling of …

Novel device with multiple FPGAs on-chip based on interposer interconnection has emerged
to resolve the IOs limit and improve the inter-FPGA communication delay. However,
new challenges arise for the placement on such architecture. Firstly, existing …

In this paper, a random walk based solver is presented which calculates the capacitances
for verifying the touchscreen design. To suit the complicated conductor geometries
in touchscreen structures, we extend the floating random walk (FRW) method for …

Stereo matching is a key step in stereo vision systems that require high accurate
depth information and real-time processing of high definition image streams. This
work presents a high-accuracy hardware implementation for the stereo matching based
on …

This paper addresses computing complex functions using unipolar stochastic logic.
Stochastic computing requires simple logic gates and is inherently fault-tolerant.
Thus, these structures are well suited for nanoscale CMOS technologies. Implementations
…

Modern caches are designed to hold 64-bits wide data, however a proportion of data
in the caches continues to be narrow width. In this paper, we propose a new cache
architecture which increases the effective cache capacity up to 2X for the systems
with …

In advanced technology nodes, the process variations deteriorate SRAM performance
and greatly affect yield. It is necessary to formulate yield estimation models to
optimize SRAMs and effectively trade-off area, performance and robustness. We propose
…

We present a metric for event detection, targeted for the analysis of CMOS asynchronous
serial data links. Our metric is used to analyze signaling strategies that allow for
coincident or nearly coincident detection of both data and event timing. The …

A hybrid memory cell usually consists of a Static Random Access Memory (SRAM) and
an embedded Dynamic Random Access Memory (eDRAM) cell; hybrid cells are particularly
suitable for cache design. A novel hybrid cache memory scheme (that has also non-…

A technique for sampling clock skew correction by adjusting the delay in the input
signal to each channel in a time-interleaved (TI) ADC is proposed. A proof-of-concept
TI ADC employing this technique was implemented in a 65 nm CMOS process. The four-…

Circuit obfuscation techniques have been proposed to conceal circuit’s functionality
in order to thwart reverse engineering (RE) attacks to integrated circuits (IC). We
believe that a good obfuscation method should have low design complexity and low …

To fully exploit the massive parallelism of many cores, this work tackles the problem
of mapping large-scale applications onto heterogeneous on-chip networks (NoCs) to
minimize the peak workload for energy hotspot avoidance. A task-resource co-…

In this paper, we explore the power/quality trade-off for streaming applications with
a shift from the computation to the communication aspects of the design. The paper
proposes a systematic exploration methodology to formulate and traverse power/…

The key characteristics of the next generation of ICs for wearable applications include
high integration density, small area, low power consumption, high energy-efficiency,
reliability and enhanced mechanical properties like stretchability and …

In this paper, two timing error masking flip-flops have been proposed, which are immune
to metastability. The proposed flip-flops exploit the concept of either delayed data
or pulse based approach to detect timing errors. The timing violations are …

Non-volatile memory (NVM) technologies have recently emerged as alternatives to traditional
SRAM-based cache memories, since NVMs offer advantages such as non-volatility, low
leakage power, fast read speed, and high density. However, NVMs also have …

In this paper, we demonstrate an energy-reduction strategy that exploits the stochastic
switching characteristics of STT-RAM write operation and propose a multiple-attempt
write technique needed for it. In contrast to the traditional approach which uses
…

In this era of Internet of Things (IoT), connectivity exists everywhere, among everything
(including people) at all times. Therefore, security, trust, and privacy become crucial
to the design and implementation of IoT devices [12]. However, it is …

The internet of things (IoT) is quickly emerging as the next major domain for embedded
computer systems. Although the term IoT could be defined in a variety of different
ways, IoT always encompasses typically ordinary devices (e.g., thermostats and …

The rapid growth of Internet-of-things and other electronic devices make a huge impact
on how and where data travel. The confidential data (e.g., personal data, financial
information) that travel through unreliable channels can be exposed to attackers.
…

Operating circuits in the sub-threshold region can save power, but at the cost of
higher susceptibility to noise. This paper analyzes various gate-level error-mitigation
designs appropriate for sub-threshold circuits. Previous works have proposed a …

With ongoing chip miniaturization and voltage scaling, particle strike-induced soft
errors present increasingly severe threat to the reliability of on-chip caches. In
this paper, we present a technique to reduce the vulnerability of caches to soft-…

As technology further scales semiconductor devices, aging-induced device degradation
has become one of the major threats to device reliability. In addition, aging mechanisms
like the negative bias temperature instability (NBTI) is known to be sensitive …

We present a fault emulation environment capable of injecting single and multiple
transient faults in sequential as well as combinational logic. It is used to perform
fault injection campaigns during design verification of security circuits such as
…

In this paper, a novel on-chip impedance calibration methodology for a LPDDR4 (low
power double data rate) application is proposed. The background calibration operates
to compensate mismatches and variations of the output NMOS drivers from process and
…

Approximate computing is an emerging design technique for error-tolerant applications.
As adders are the key building blocks in many applications, approximate adders have
been widely studied recently. However, existing approximate adders may introduce …

RRAM-based memory is a promising emerging technology for both on-chip and stand-alone
non-volatile data storage in advanced technologies. In addition to its small dimensions,
the RRAM device has many technological advantages including its low-…

The physical dimensions of standard cells constrain the dimensions of power networks,
affecting the on-chip power noise. An exploratory modeling methodology is presented
for estimating power noise in advanced technology nodes. The models are evaluated
…

With continuous and aggressive technology scaling, suppressing the stand-by power
is among the top priorities for SRAM design. Switching off the less-frequently accessed
blocks is an efficient way to reduce the stand-by power, provided that the …

We present the design of stochastic computing systems based on sequential logic to
implement arbitrary polynomial functions. Stochastic computing is an emerging alternative
computing paradigm that performs arithmetic operations on real-valued data …

Despite many attractive advantages, Null Convention Logic (NCL) remains to be a niche
largely due to its high imple- mentation costs. Using emerging spintronic devices,
this paper proposes a Domain-Wall-Motion-based NCL circuit design methodology that
…

Inductive links have been proposed as an inter-tier interconnect solution for three-dimensional
(3-D) integrated systems. Combined with signal multiplexing, inductive links achieve
high communication bandwidth comparable to that of through silicon vias. …

With extreme miniaturization of traditional CMOS devices in deep sub-micron design
levels, the delay of a circuit, as well as power dissipation and area are dominated
by interconnections between logic blocks. In an attempt to search for alternative
…

Variability is the real big challenge for integrated circuits. Today, simulators help
to estimate the effect of variability, but fail to capture real workload dynamics
and user interactions, which are fundamental to mobile devices. This paper presents
…

Due to size, longevity, safety, and recharging concerns, energy harvesting is becoming
a better choice for many wearable embedded systems than batteries. However, harvested
energy is intrinsically unstable. In order to overcome this drawback, non-…

Models of power sources are essential elements in the simulation of systems that generate,
store and manage energy. In spite of the huge difference in power scale, they perform
a common function: converting a primary environmental quantity into power. …

In recent years, the semiconductor industry has been witnessing an increasing reuse
of hardware IPs for System-on-Chip (SoC) designs and embedded computing systems on
FPGA platforms with hard-core processors. The IP-reuse comes with an increasing …

In today’s competitive market, a company’s success is strongly dependent on delivering
sophisticated and state-of-the-art IPs prior to their competitors. To take a short
cut, a company may resort to reverse engineering or pirating their competitor’s IP.

…

Inherent stochastic physical mechanisms in emerging nonvolatile memories (NVMs), such
as resistive random-access-memory (RRAM), have recently been explored for hardware
security applications. Unlike the conventional silicon Physical Unclonable Functions
…

We consider how the I-V characteristics of emerging transistors (particularly those
sponsored by STARnet) might be employed to enhance hardware security. An emphasis
of this work is to move beyond hardware implementations of physically unclonable …

The emerging nonvolatile memory (NVM) technologies have demonstrated great potentials
in revolutionizing modern memory hierarchy because of their many promising properties:
nanosecond read/write time, small cell area, non-volatility, and easy CMOS …

Authentication of electronic devices has become critical. Hardware authentication
is one way to enhance security of a chip. Along with software, it makes it harder
for an intruder to access any computer, smart-phone, or other devices without …

This paper proposes a centralized approach for connection allocation for TDM-based
NoCs by making use of dedicated hardware unit called NoCManager that employs trellis-based
search algorithm enabling dynamic parallel multi-path, multi-slot allocation. …

Recently, work has been done on using nonvolatile cells, such as Spin Transfer Torque
RAM (STT-RAM) or Magnetic RAM (M-RAM), to construct last level caches (LLC). These
structures mitigate the leakage power and density problem found in traditional SRAM
…

Technology scaling of tiled-based CMPs reduces the physical size of each tile and
increases the number of tiles per die. This trend directly impacts the on-chip interconnect;
even though the tile population increases, the inter-tile link distances scale …

Large-scale MPSoCs requires a scalable and dynamic real-time (RT) task scheduler,
able to handle non-deterministic computational behaviors. Current proposals for MPSoCs
have limitations, as lack of scalability, complex static steps, validation with …

3D die stacking and 2.5D interposer design are promising technologies to improve integration
density, performance and cost. Current approaches face serious issues in dealing with
emerging security challenges such as side channel attacks, hardware …

Contemporary mobile platforms employ embedded graphic processing units (GPUs) for
graphics-intensive games, and dynamic voltage and frequency scaling (DVFS) policies
are used to save energy without sacrificing quality. However, current GPU DVFS policies
…

To meet energy and quality of service (QoS) constraints in consumer-based embedded
devices (CEDs), configurable caches can be tuned to a best configuration that consumes
the least amount of energy while adhering to QoS expectations. However, due to …

Power/energy reduction is of uttermost importance for applications with stringent
power/energy budget such as ultra-low power and energy-harvested systems. Aggressive
voltage scaling and in particular Near-Threshold Computing (NTC) is a promising …

Leakage power minimization is one of the key aspects of modern multi-million low power
system-on-chip (SoC) design. In post timing-closure phase, leakage-in-place-optimization
(LIPO) is generally adopted to reduce leakage power by swapping high-leaky …

Due to the reducing transistor feature size, the susceptibility of modern circuits
to radiation induced errors has increased. This, as a result, has increased the likelihood
of multiple transients affecting a circuit. An important aspect when modeling …

Atomistic-based approaches accurately model Bias Temperature Instability phenomena,
but they suffer from prolonged execution times, preventing their seamless integration
in system-level analysis flows. In this paper we present a comprehensive flow that
…

Negative bias temperature instability (NBTI) has emerged as a critical challenge to
lifetime reliability of computing systems. Traditionally, temperature-aware methodologies
are used to mitigate the impact of NBTI on aging and degradation of computing …

An all-digital self-adaptive clock generation system capable of autonomously adapt
the clock frequency to compensate the effects of static spatially heterogeneous (SSHet)
PVTA variations is presented. The design uses time-to-digital converters (TDCs) as
…

This paper introduces a novel design of reconfigurable Spintronic Threshold Logic
Gate (STLG), which employs spintronic weight devices to perform current mode weighted
summation of binary inputs, whereas, the low voltage spintronic threshold device …

To address the high energy consumption issue of SRAM on GPUs, emerging Spin-Transfer
Torque (STT-RAM) memory technology has been intensively studied to build GPU register
files for better energy-efficiency, thanks to its benefits of low leakage power, …

In this paper, study of different digital logic circuits developed using two-BDT ballistic
nanostructure is presented. New D flip-flop (DFF) based on the same nanostructure
is also proposed. The logic structure comprises two ballistic deflection …

Emerging non-volatile memories (NVMs), which include PC-RAM and STT-RAM, have been
proposed to replace DRAM, mainly because they have better scalability and lower standby
power. However, previous research has demonstrated that these NVMs cannot …

This paper describes a low overhead, offline frequent value encoding (FVE) solution
to reduce the write energy in multi-level/triple-level cell (MLC/TLC) non-volatile
memories (NVMs). The proposed solution, which does not require any runtime software
…

Multi-port memories are widely used as shared memory, such as register files, in a
microprocessor system, and its number of ports and capacities are significantly increasing
with every product generation. However, with technology advancements, multi-…

This paper deals with obtaining the minimum operating voltage of memory arrays based
on TFET SRAM cells. First, we compare the I-V characteristics of two TFETs and one
FDSOI using SPICE simulations based on 20nm technology models. The results reveal
…

Embedded computing systems include several off-chip serial links, that are typically
used to interface processing elements with peripherals, such as sensors, actuators
and I/O controllers. Because of the long physical lines of these connections, they
…

Out of the many options available for thermal simulation of digital electronic systems,
those based on solving an RC equivalent circuit of the thermal network are the most
popular choice in the EDA community, as they provide a reasonable tradeoff …